612434

Eminent EM6600 e-Domotica Manual

26
Zoom out
Zoom in
Previous page
1/30
Next page
26 | ENGLISH
3. Subsequently, the wireless transmitter will attempt to obtain contact with the Z-
Wave Master device in order to be excluded from the network.
Note: It is important to consult with the user guide for the Z-Wave Master device, on
the desired Z-Wave network, in order to determine how to include and exclude other
Z-Wave products to the Z-Wave network.
6.2.4 Press button 5 times – Calibration function
When mounting Energy Reader on a mechanical meter it is necessary to calibrate the
sensor head to ensure a correct reading of consumption from the meter. Press 5 times
on the sensor button once the sensor head has been mounted to start the calibration.
The LED will start flashing to indicate that calibration has begun.
The calibration takes approx. 5-10 minutes, and the LED will start to flash in a slower
rate as the calibration is nearing completion.
When the calibration is completed the LED will turn off. Hereafter the LED will flash
once each time a rotation have been registered from the power meter.
Note! If the LED does not turn off and begins flashing rapidly instead after calibration
is completed, this means that the Energy Reader could not make a proper reading of
the rotational dial on the power meter and alternative mounting of the sensor head
should be attempted.
6.2.5 Press and hold button for 5 seconds – Fine tuning mode
In order to ensure a correct reading of consumption data from mechanical meters it
may be necessary to make fine tuning adjustments to the placement of the sensor
head. Press and hold the button for 5 seconds to begin the fine tuning function.
• The LED will begin to flash rapidly. The brightness of the LED will vary depending
on how optimal reading conditions are registered by the sensor head.
• Place the sensor head where the LED will glow with the brightest light. Then
press the sensor button 5 times to start the calibration function again.
6.2.6 Press button 7 times – Reset to factory default
Press seven times on the sensor button to reset the wireless transmitter. - The LED
will respond with:
3 short flashes – 2 seconds being lit, or longer if a longer period of data is stored –
and again 3 short flashes to indicate that the resetting has been completed correctly.
Note! All data stored in the Energy Reader will be deleted permanently. Only reset the
wireless transmitter if experiencing problems while setting up the wireless connection
between the transmitter and USB receiver, or after consulting the hotline support.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eminent EM6600 e-Domotica at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eminent EM6600 e-Domotica in the language / languages: English as an attachment in your email.

The manual is 3,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eminent EM6600 e-Domotica

Eminent EM6600 e-Domotica User Manual - Dutch - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info