612431
10
Zoom out
Zoom in
Previous page
1/14
Next page
10 | ENGLISH
1. You can choose to mount the transmitter
to the wall either by using 2 screws or
using the included adhesive pad.
Choose a correct location for the flood
detector transmitter. We advise to mount
the flood detector transmitter at least 1.5
meter above ground for optimal wireless
communication and to avoid the flood
detector transmitter come into contact
with flood. The transmitter should never
be submerged in flood.
The cable length from the transmitter to
the sensor head is 3 meters.
2. If you did not remove the bracket of the
transmitter yet, remove the bracket (2) of
the transmitter (6). This bracket has
several holes for screws.
3. Apply the bracket to the wall or ceiling
and mark the spots for the two drilling
holes. Or you can use the adhesive pads
instead of screws.
4. Now drill the two holes and fill them with
the supplied plugs (1).
5. Mount the wall bracket (2) by using the
two supplied screws (5) and carefully
tighten the screws.
6. Once the bracket has been mounted, you
can place the EM6592 transmitter on the
bracket by sliding it from the top down.
Fix the bracket to the transmitter by
fastening the screw (7) at the bottom.
Image 10
6.2 Mounting the sensor head and cable
1. It is recommended to mount the sensor head at the lowest level of the floor,
where you might expect a flooding. For example, if your washer is located in the
basement, you can mount the sensor head at the lowest point, near to the
washer.
2. Mount the sensor head (refer to image 1, chapter 1.1) on the desired position on
the wall with the sensor clip (4), using the adhesive pad or using a screw (5).
3. Mount the cable clips on the wall between the transmitter and the sensor head.
Each cable clip (3) can be mounted either with a screw or with an adhesive pad.
4. Click the cable in the cable clips. If the cable is too long, you can roll up the
cable.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eminent EM6592 e-Domotica at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eminent EM6592 e-Domotica in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eminent EM6592 e-Domotica

Eminent EM6592 e-Domotica User Manual - German - 14 pages

Eminent EM6592 e-Domotica User Manual - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info