701862
6
Zoom out
Zoom in
Previous page
1/34
Next page
- 5 -
6) Adjust the tilt angle of the fan head to your desired position and then fully tighten both the small and big
black knobs.
3. Fan guards and blade assembly
1) To assemble the fan guards and blade, first remove the 4 rear guard fastening screws from the motor. (fig.
1)
2) Fit the rear guard into position (with the handle on the back of the guard at the top) and refit the 4 screws
and tighten. (fig. 2)
3) Slide the fan blade onto the spindle ensuring the screw is lined up with the “flat” surface on the spindle as
shown. (fig. 3)
4) Push on until the end of the spindle is flush with the end of the fan blade hole, then tighten the screw. (fig.
4)
5) Open up all locking clips on the sides of the front guard. (fig.5)
6) Place the front guard into position by lining up the location plate over the top of the rear guard as shown
and push down. (fig.6)
7) Secure the two guards by closing the clips over the outer rim. (fig. 7)
8) Then using the small nut and bolt, fasten the two guards together at the bottom of the guards. (fig.8)
OPERATING INSTRUCTION
1. Plug the power cord into a suitable socket.
2. Switch on the fan by using the speed switch on the motor housing. “0” = off, “I” = low speed, “II= medium
speed, “III” = high speed.
3. Tilting angles: You can loosen the big and small black knobs on the motor bracket to adjust the fan to your
preferred elevation. Then fasten the elevation by tightening the knobs.
4. Oscillation: to make the fan head oscillate, push down the oscillation knob on the top of the motor. To stop
the fan head from oscillating, pull up the oscillation knob.
CLEANING
1. Before servicing the fan and after each occasion of use, switch off the appliance and unplug the mains cable
from the socket.
2. Never immerse the appliance in water (danger of short-circuit). To clean the appliance, only wipe it down
with a damp cloth and dry it carefully. Always take out the mains plug first.
3. Take care that excessive dust does not build up in the air-intake and air-outlet grille, and clean it occasionally
using a dry brush or vacuum cleaner.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Emerio FN-120952 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Emerio FN-120952 in the language / languages: English, German, Dutch, Swedish, Finnish as an attachment in your email.

The manual is 2,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info