794830

Elro PK4910 Manual

6
Zoom out
Zoom in
Previous page
1/36
Next page
- 6 -
6. Test if the device works properly by pressing and holding the test/mute button for
approximately 3 seconds. If the device is working properly, it will beep four times and flash red.
More tips on how to install your carbon monoxide detector? Go to www.elro.eu
See back page (cover) for drilling template for vertical installation!
Functionality
Mode
Light signal
Audio signal
Explanation
Standby
Green flashes 1 x
per 40 sec.
No sound
Detector functions
correctly
Test
Red flashes 4 x
quickly, followed
by 5 sec. short
break
4 x quickly, followed
by 5 sec. break
Detector functions
correctly
CO alarm
Red flashes 4 x
quickly, followed
by 5 sec. break
4 x quickly, followed
by 5 sec. break
Detector has detected
carbon monoxide
CO alarm mute
Red flashes 1x per
40 sec.
No sound
Alarm signal is muted
CO alarm memory
Green flashes 3 x
per 40 sec.
No sound
The detector has issued
a CO alarm in the last
48 hours
Low battery
voltage
Yellow flashes 1 x
per 40 sec.
1 x per 40 sec.
Low battery voltage,
replace device asap
Low battery
voltage mute
Yellow flashes 1 x
per 40 sec.
No sound
Low battery warning
muted for approx. 10 h.
Siren error
Yellow flashes 2 x
per 8 sec.
No sound
Siren error detected,
replace device asap
Sensor error
Yellow flashes 2 x
per 8 sec.
2 x per 8 sec.
Sensor error detected,
replace device asap
End of life
Yellow flashes 3 x
per 40 sec.
3 x per 8 sec.
End of life, replace
device asap
Standby
In the standby mode, the CO level (if this is lower than 20 ppm it will display 0) and the room
temperature are shown, in an alternating manner. If the CO level exceeds 20 ppm, only the CO
level is displayed. This detector is equipped with a night mode, which means that the standby LED
is automatically switched off in dark areas.
Alarm
If the CO level in the room is too high, the carbon monoxide detector switches to the alarm mode
according to the scheme below.
• 030 – 049 PPM: Alarm signal after 120 minutes
• 050 – 099 PPM: Alarm signal after 60 - 90 minutes
• 100 – 299 PPM: Alarm signal after 10 - 40 minutes
• > 300 PPM: Alarm signal within 3 minutes
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro PK4910 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro PK4910 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1.21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info