536726
54
Zoom out
Zoom in
Previous page
1/62
Next page
52
Press to initiate ARM.
Press to initiate Partial Arm.
Press to initiate Holiday Arm.
Press to Disarm the system.
Press to turn OFF all of Green Control.
Press to turn the Siren OFF.
Press to turn the Siren ON.
Press to Listen-In via the Smart Home
Box Microphone.
Press to stop Listen-In
Note: Listen-in will be automatically cancelled after 5
minutes if not cancelled manually.
Press to interrogate the system status. A
message playing the latest status can be heard.
Press to read the status of AC power
supply.
Press to end the remote system control
and hang up the Smart Home Box line.
BATTERY MONITORING
All system devices continuously monitor their battery
condition. The Smart Home Box also monitors the
battery condition of all PIR and Magnetic detectors. If
the battery level of any device drops below acceptable
levels then its low battery indication will be activated.
In addition if any PIR or Magnetic Contact detector has
a low battery status it will be recorded by the Smart
Home Box and a message stored in the event log.
In the event of AC adaptor being disconnected from the
Smart Home Box, the Smart Home Box by consuming
the DC rechargeable battery can sustain 8 hours of
normal operation (under Disarm mode). However, the
battery for that device should be replaced as soon as
possible.
Note: Before removing the battery cover on any device
to replace the battery ensure that the system is put into
Test mode to avoid initiating a Full Alarm condition.
The low battery indication for each system component
is as follows:
Smart Home Box
During a period of mains supply interruption, the Smart
Home Box will be powered by the rechargeable backup
batteries. Under this circumstance, a radio signal will
be emitted to the central monitoring station or the
telephone voice dialer will call the set numbers right
away; this procedure will repeat again after 4 hours.
Under normal battery conditions the Power LED on the
panel will flash at 1s intervals.
Remote Control
When the Remote Control is operated under low
battery conditions the transmit LED will continue to
flash after the button has been released.
Under normal battery conditions the LED will
extinguish when the button is released.
PIR Detectors
Under low battery conditions the LED behind the
detector lens will flash when movement is detected to
indicate that the battery needs to be replaced.
Under normal battery conditions the LED does not
illuminate unless the PIR detector is in Walk Test
mode.
Magnetic Contact Detectors
Under low battery conditions, when the Detector is
activated the transmit LED will be illuminated for
approximately 1s as the door/window is opened.
Under normal battery conditions the LED will not
illuminate as the Detector is operated, (unless the
Detector is in Test Mode with the battery cover
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro HIS20SF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro HIS20SF in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info