Manual Elro HIS20SF (page 12 of 62) (English, German, Dutch, French)

536726

Zoom out

Zoom in

1/62

2. Carefully drill out the required mounting holes in

the rear cover using 3mm drill according to whether

the unit is being mounted in a corner or against a

flat wall.

Note: Using 1

mounting hole to fulfill corner

mounting installation, while 2

mounting hole for

flat wall installation.

Corner mounting

3. Using the rear cover as a template, mark the

positions of the fixing holes on the wall.

4. Fix the rear cover to the wall using the two 18mm

No.4 screws and 25mm wall plugs, (a 5mm hole

will be required for the wall plugs). Do not

over-tighten the fixing screws as this may distort or

damage the cover.

5. Configure the PIR detector as described below.

Remember that on initial installation that the device

needs to be tested and should therefore be set in

Walk Test Mode.

6. Check that the detector PCB is located and set in

the correct position to provide the required

detection range. To adjust the PCB position,

simply slide it up or down ensuring that the location

legs are aligned with the required position number

marked on the board.

7. To refit the PIR detector to the rear cover and

locate the clips in the top edge into the rear cover.

Push the lower edge of the detector into place and

refit the fixing screw in the bottom edge of the PIR

to secure in position. Do not over-tighten the

fixing screws as this may damage the casing.

SETTING THE PIR DETECTORS

Located on the PCB of the PIR Detector is a

two-position DIP switch (SW2). When conducting the

Walk Test, ensure that the DIP switch SW2 is set as

follows:

SW2 DIP1 DIP2

ON 9

OFF 9

1. DIP1 of SW2 is used to configure the PIR Detector

for walk test mode, which allows the operation of

the detector to be checked during installation

without triggering a Full Alarm.

ON Walk Test mode

OFF Normal mode

Note: On initial installation the detector should be

set into Walk Test mode ready for testing. Upon

completion of Walk Test mode, set DIP1 of SW2 to

OFF for normal detection mode.

2. The PIR Detector incorporates an anti-false alarm

feature designed to compensate for situations

where the detector may be affected by

environmental changes, (e.g. insects, air

temperature, etc). This feature is called

“sensitivity detection” and may be selected for high

or low detection.

The recommended setting is for high sensitivity

detection. However, in cases of extreme

environmental problems or if unattributable false

alarms are experienced, it may be necessary to

select low sensitivity detection.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elro HIS20SF in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elro HIS20SF Manual

Product: