708679
4
Zoom out
Zoom in
Previous page
1/4
Next page
4
Tamper Protection
Tamper switch is set inside the housing to prevent it from being forcibly
removed from the wall. Removing the unit from backplate will release the
tamper switch and generate a full alarm condition.
Install Power Adapter (Optional)
The power adapter is an optional accessory. An optional 600mA @ 6V DC
power adapter can be purchased if needed. A cable track is set inside the unit
for you to secure the power adapter. Please install the power adapter as
follows:
Maintenance
*
Do not immerse this unit in water or any other liquid.
*
Four 1.5V Alkaline LR14 batteries are supplied. When battery is low, a red
LED will flash every 30 seconds. When this situation occurs, replace the
batteries as soon as possible.
Troubleshooting
The troubleshooting table lists some possible causes and solutions. Please
contact your original retailer or nearest service center if the below solutions
cannot solve your problem.
Symptom
Possible Cause
Recommendation
LED indicator stops
displaying
No battery is inserted or
battery is flat
Check if 4 batteries are inserted
properly
Failure
Send the unit to the service
center and do not open it
The display function of
LED indicator is
operating properly, but
the siren doesn’t
respond to alerts and
system changes.
1. The binding process
has failed
2. The siren cannot
communicate with the
gateway.
1. Please follow the instructions
for Manual binding.
2.Place the siren closer to the
gateway.
Reset to factory default:
To reset AS80SR11A back to factory default state:
1.
Insert the batteries into the unit
2.
Press and hold the learning key “F” (as shown in Figure 5) for more than 3
seconds until the green strobe LED turns off, then release the learning key.
The Green LED will flash repeatedly. This implies it has now entered
binding mode and is waiting to receive binding signals from the gateway.
3.
Press and hold the learning key for more than 6 seconds and release
within 30 seconds, during which it will sound every 0.5 seconds with green
LED turned on. The learning procedure is completed when a longer beep
tone has sounded and the LED will flash orange every 2 seconds.
Specifications
Power adaptor (option)
600 mA@6V DC
Battery Type
1.5V LR14 x 4
Battery Life
About one year in standby mode at 25°C
Operating Frequency
868MHz
** Specifications are subject to change and improvement without notice.
2.
Route the cable along the
cable track.
1.
Connect the plug of
power adapter to the DC
jack inside the unit.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro AS80SR11A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro AS80SR11A in the language / languages: English as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info