620749

Elro AB600S-2B Manual

3
Zoom out
Zoom in
Previous page
1/6
Next page
E
N
G
L
I
S
H
D
E
U
T
S
C
H
D
E
U
T
S
C
H
REMOTE CONTROL
The Remote Control is the core of the system and controls ON & OFF status of On/Off Receiver for a
maximum of two pieces in one zone. By adopting the house code to differentiate the specific zone, it
can control the On/Off Receiver for a maximum of 8 pcs.
1. INSERTING THE BATTERY:
Remove the battery cover. Fit the 23A 12V battery in the compartment provided with battery lead, '+' to
'+' and '-' to '-'.
By pressing any key, the red LED will illuminate, which implies that the battery has been inserted
properly.
Replace the battery cover.
2. SETTING THE HOUSE CODE
In order for On/Off Receiver to communicate with the Remote Control, it is essential that the same
house code is used for all components.
In the front of the casing, you will find the house code knob, ranging from A to D.
Note: Ensure that the house code between On/Off Receiver must be the same as that of Remote
Control, otherwise, they cannot communicate with each other.
3. IDENTIFYING THE UNIT CODE
The Transmitter is able to control 2 pieces of On/Off Receivers as maximum in one specific zone.
The unit code of On/Off Receiver is fixed ex-factory indicating unit 1 or unit 2 respectively. In the front
of the casing, you will find 4 buttons, two of which bigger buttons are ON for unit 1 and unit 2. The rest
of smaller buttons are OFF for unit 1 and unit 2. You should identify each receiver a unit code for
identification purpose, so that Remote Control can control ON & OFF status of Receiver through its ON
& OFF button.
ON/OFF RECEIVER
The On/Off Receiver is used to receive the Radio Frequency signal from the Remote Control, and
through the Remote Control controls the ON & OFF status of small home appliances, such as coffee
makers, kettles, radios and fans etc.
1. SETTING THE HOUSE CODE:
In order for all Receivers to communicate with the Remote Control, it is essential that the same house
code is used for all components.
In the rear of the casing, you will find the house code knob, ranging from A to D. If the house code of
your Remote Control is set for “A”, the house code of On/Off Receiver must be set for “A” too.
Note: Ensure that the house code between On/Off Receiver must be the same as that of the Remote
control(s), otherwise, they cannot communicate with each other.
2. IDENTIFYING THE UNIT CODE:
The unit code of On/Off Receiver is fixed ex-factory indicating unit 1 and unit 2 respectively. The
Remote Control is able to control 2 pieces of On/Off Receiver as maximum in one zone. By adopting
the house code to differentiate the specific zone, it can control the On/Off Receiver for a maximum of
8 pcs.
When adopting a number of On/Off Receivers , you should identify the unit code of each receiver for
identification purpose, so that the Remote Control can control ON & OFF status of each Remote
Control through its ON & OFF button.
E1
Wenn Sie mehr als einen Schaltempfänger im Einsatz haben, lesen Sie den Gerätecode eines jeden
Schaltempfängers ab und merken (oder notieren) Sie sich die Zuordnung, damit Sie wissen, mit
welcher Taste auf Ihrer Fernbedienung Sie den betreffenden Schaltempfänger ein- und ausschalten
können.
3. BEDIENUNG
Wenn Sie die Einstellung des Hauscodes abgeschlossen haben, stecken Sie den Schaltempfänger in
die Steckdose. Das rote LED am Schaltempfänger leuchtet nun. Stecken Sie den Netzstecker des
gewünschten kleinen Haushaltsgeräts in die Steckdose des Schaltempfängers und stellen Sie den
Schalter des Haushaltsgeräts auf EIN.
Wenn Sie nun auf Ihrer Fernbedienung die Taste für „EIN“ drücken, wird das am Schaltempfänger
angesteckte kleine Haushaltsgerät eingeschaltet, und das rote LED am Schaltempfänger leuchtet.
Wenn Sie dann auf Ihrer Fernbedienung die Taste für „AUS“ drücken, wird das am Schaltempfänger
angesteckte kleine Haushaltsgerät ausgeschaltet, und das rote LED am Schaltempfänger erlischt.
Tastendruck Am Schaltempfänger LED am
angestecktes kleines Schaltempfänger
Haushaltsgerät
Taste „EIN“ EIN leuchtet rot
auf der Fernbedienung
Taste „AUS“ AUS AUS
auf der Fernbedienung
D2
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elro AB600S-2B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elro AB600S-2B in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info