614476
50
Zoom out
Zoom in
Previous page
1/52
Next page
48
T R O U B L E S H O O T I N G
Condition Cause
See page(s)
Needle thread 1. The needle is not threaded correctly. 25
breaks 2. The needle thread tension is too tight. 18
3. The needle is bent or blunt. 20
4. The needle is not inserted correctly. 20
5. The thread is either too heavy or too fine for the needle. 20
Bobbin thread 1. The bobbin thread is not threaded correctly in the bobbin case. 24
breaks
2. Lint has collected in the bobbin case.
3. The bobbin is damaged and does not turn smoothly.
41-42
Change bobbin
Needle breaks 1. The needle is not inserted correctly. 20
2. The needle is bent or blunt. 20
3. The needle clamp screw is loose. 20
4. The needle thread tension is too tight. 18
5. The needle is too fine for the fabric being sewn. 20
Skipped stitches 1. The needle is not inserted correctly. 20
2. The needle is bent or blunt. 20
3. The needle and/or the thread are not suitable for the fabric being sewn.
4. A stretch needle is not being used for sewing stretch, very fine and
20
synthetic fabrics. 20
5. The needle thread is not threaded correctly. 25
6. The foot pressure dial is not adjusted correctly. 15
7. The wrong needle is being used. 20
Seam puckering 1. The needle thread tension is too tight. 18
2. The machine is not threaded correctly. 25
3. The needle is too large for the fabric being sewn. 20
4. The stitch length is too long for the fabric. 11
5. The foot pressure dial is not set correctly.
Place lightweight teara way stabilizer under lightweight fabrics.
15
Slipping fabric 1. The foot pressure dial is not adjusted correctly. 15
2. The correct presser foot is not being used. 5-6
Fabric does not 1. The feed dog is packed with lint. 41-42
feed smoothly 2. The pressure foot dial is not set correctly. 15
3. The stitches are too short. 11
4. The feed dog was not raised after being lowered. 16
5. The correct presser foot is not being used. 5-6
Gathering 1. The needle thread tension is too loose. 18
2. The needle is either too large or too small for the thread. 20
3. The stitch length is too long for fabric. 11
Machine does not 1. The machine is not plugged in. 9
work 2. A thread is caught in the hook area. 41-42
3. The bobbin winder spindle is still in the winding position. 23
Stitches are 1. The fine adjustment screw is not set correctly. 19
distorted 2. The correct presser foot is not being used. 5-6
3. The needle thread tension is too tight. 18
4. The stitch length is not suitable for the fabric being sewn.
5. Use stabilizer for fine or stretch fabrics.
11
use stabilizer
Sensor 1. Interfacing is not being used with fabrics. 28
buttonholes do not
work
Noisy operation 1. Threads have been caught in the hook area. 41-42
2. Lint has built up in the bobbin holder or hook area. 41-42
Machine stops and 1. Threads have been caught in the hook area. 41-42
the message Lo 2. Lint has built up in the bobbin holder or hook area. 41-42
appears. 3. The machine is not threaded properly. 25
4. The fabric is too heavy. 20
Machine stops and 1. Machine needs servicing. Contact Elna
message E1 ~ E5
appears.
service center
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elna eXperience 660 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elna eXperience 660 in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info