703998
17
Zoom out
Zoom in
Previous page
1/124
Next page
15
Press the auto-lock button to sew a locking stitch
immediately. The machine will automatically stop.
When the machine is stopped, press the auto-lock
button to blink the LED signal u. The machine will
immediately sew locking stitches and automatically
stop when the machine is started.
• When any other stitches are selected;
Press the auto-lock button to sew a locking stitch
at the end of current pattern. The machine will
automatically stop.
When the machine is stopped, press the auto-lock
button to blink the LED signal u. The machine will
sew a locking stitch at the end of the current pattern
and automatically stop when the machine is started.
The machine will trim the threads automatically after
locking the stitch when the auto thread cutting is
turned on (refer to page 110).
r Needle up/down button
Press this button to bring the needle bar up or down.
The machine will stop with the needle in down position.
However, you can change the needle stop position in the
machine setting mode (refer to page 108).
t Presser foot lifter button
The presser foot will go up or go down by pressing this
button.
You can also use the presser foot lifter and knee lifter to
raise and lower the presser foot (refer to page 29-30).
y Thread cutter button
After nish sewing, press this button to trim the threads.
The needle bar automatically rises after trimming the
threads (refer to page 35).
The LED signal i blinks when the machine trims
threads.
Machine Operating Buttons
q Start/stop button
Press this button to start or stop the machine.
The machine starts running slowly for the rst few
stitches, it then runs at the speed set by the speed control
slider. The machine runs slowly as long as this button is
pressed.
The button will turn red when the machine is running, and
green when it has been stopped.
Pressing and holding this button while sewing will slow
down the sewing speed and the machine will stop when
the button is released.
NOTE:
The start/stop button cannot be used when the foot
control is connected to the machine.
You can select the desired start-up speed from
slow, medium or high (refer to page 109).
NOTE:
The thread cutter button does not function:
- directly after turning on the power.
- when the presser foot is raised with the foot lifter.
- after being pressed 3 times in a row.
Use the thread cutter on the face cover if the thread is
#30 or thicker (refer to page 35).
w Reverse button
• When stitch pattern U1, U4, U8-U10, Q1-Q3, or
BR1-BR6, is selected;
NOTE:
There will be particular functions of the reverse
button when stitch pattern U2, U3, B2, B13, or B14
is selected. Refer to pages 36, 53-54, 59 and 98 for
instructions.
e Auto-lock button
• When stitch pattern U1, U4, U8-U10, Q1-Q3, or BR1-
BR6, is selected;
The machine will sew in reverse as long as the
reverse button is pressed. Release the button to sew
forward.
When the machine is stopped and foot control is
disconnected, the machine will sew in reverse slowly
as long as the reverse button is pressed. Release the
button to stop the machine.
• When any other stitches are selected;
If you press the reverse button when sewing any other
patterns, the machine will immediately sew locking
stitches and automatically stop.
q
w
e
r
t
y
u
i
U: Q: BR:
U: Q: BR:
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elna eXcellence 780 plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elna eXcellence 780 plus in the language / languages: English as an attachment in your email.

The manual is 24,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elna eXcellence 780 plus

Elna eXcellence 780 plus User Manual - German - 124 pages

Elna eXcellence 780 plus User Manual - French - 124 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info