612699

Elm 327 Manual

46
Zoom out
Zoom in
Previous page
1/94
Next page
CAN Receive Filtering - the CRA Command
When receiving CAN data, the ELM327 actually
retrieves every message from the CAN bus, and then
decides whether or not to display it, based on criteria
that you or the firmware set. The ‘CAN Receive
Address’ or CRA command may be used to define
this criteria for you, in one simple step.
As an example, assume that the only messages
that you wish to see are those that have the CAN ID
7E9. To see only them, tell the ELM327 that the
receive address should be 7E9:
>AT CRA 7E9
and the ELM327 will set the necessary values so that
the only messages that are accepted are the ones with
ID 7E9.
If you do not want an exact address, but would
prefer to see a range of values, for example all the
OBD addresses (those that begin with 7E), then simply
use an ‘X’ for the digit that you do not want the
ELM327 to be specific about. That is, to see all
messages with CAN IDs that start with 7E (7E0, 7E1,
7E2,... 7EE, and 7EF), send:
>AT CRA 7EX
and the ELM327 will set the necessary values for you.
This command works exactly the same way for the
29 bit IDs. For example, if you wish to see all
messages that are being sent from the engine ECU
(address 10) to the scan tool (address F1), then you
can send:
>AT CRA XX XX F1 10
and all the settings will be taken care of for you.
If you wish to be more specific and see only the
OBD replies sent by the engine to the scan tool, you
would say:
>AT CRA 18 DA F1 10
and again, the ELM327 makes the necessary changes
for you.
Perhaps you do not care which device is sending
the information, but you want to see all messages that
start with 18 DA and are being sent to the scan tool.
For this, use the character ‘X’ to tell the ELM327 that
you do not care what value a digit has:
>AT CRA 18 DA F1 XX
and the ELM327 takes care of the details for you.
When working with J1939 data, the ELM327
normally formats the data for you, in order to separate
the priority from the PGN information. This is usually
not a concern when using the CRA command, except
when you are trying to filter for a specific priority. For
example, you might typically see:
>AT MA
3 0FE6C 00 FF FF FF FF FF FF 40 B5
6 0FEEE 00 15 50 FF FF FF FF FF FF
6 0FEF5 00 FE FF FF FF 19 00 23...
The single priority digit out front (the 3 or 6 above)
as well as the leading 0 with the PGN information are
actually part of the first two digits (5 bits) of the ID, and
need to be interpreted as such, in order to use the
CRA command. It may be easier if you turn off the
J1939 header formatting in order to see this:
>AT JHF0
OK
>AT MA
0C FE 6C 00 FF FF FF FF FF FF 40 B5
18 FE EE 00 15 50 FF FF FF FF FF FF
18 FE F5 00 FE FF FF FF 19 00 23...
This more clearly shows the four bytes that need
to be defined for the CRA command to be set. To
search for all messages that begin with 6 0FEF5, you
would actually need to send the command:
>AT CRA 18 FE F5 XX
In summary then, the CRA command allows you
to tell the ELM327 what ID codes to look for, and the
letter ‘X’ may be used in it to represent any single digit
that you do not want the ELM327 to be specific about.
This is usually selective enough for most applications,
but occasionally, there is a need to be specific down to
the bit level, rather than to the nibble. For those
applications, you will need to program a separate
mask and filter, as we show in the next section.
ELM327
46 of 94ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
… 46 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elm 327 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elm 327 in the language / languages: English as an attachment in your email.

The manual is 0,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info