612699
10
Zoom out
Zoom in
Previous page
1/94
Next page
Several parameters within the ELM327 can be
adjusted in order to modify its behaviour. These do not
normally have to be changed before attempting to talk
to the vehicle, but occasionally the user may wish to
customize these settings – for example by turning the
character echo off, adjusting a timeout value, or
changing the header bytes. In order to do this, internal
‘AT’ commands must be used.
Those familiar with PC modems will immediately
recognize AT commands as a standard way in which
modems are internally configured. The ELM327 uses
essentially the same method, always watching the
data sent by the PC, looking for messages that begin
with the character ‘A’ followed by the character ‘T’. If
found, the next characters will be interpreted as an
internal configuration or ‘AT’ command, and will be
executed upon receipt of a terminating carriage return
character. If the command is just a setting change, the
ELM327 will reply with the characters ‘OK’, to say that
it was successfully completed.
Some of the following commands allow passing
numbers as arguments in order to set the internal
values. These will always be hexadecimal numbers
which must generally be provided in pairs. The
hexadecimal conversion chart in the OBD Commands
section (page 30) may be helpful if you wish to
interpret the values. Also, you should be aware that for
the on/off types of commands, the second character is
the number 1 or the number 0, the universal terms for
on and off.
The remainder of this page, and the two pages
following provide a summary of all of the commands
that the current version of the ELM327 recognizes. A
more complete description of each command begins
on page 12. Note that the settings which are shown
with an asterisk (*) are the default values.
10 of 94
ELM327
ELM327DSJ Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
AT Command Summary
AT Commands
General Commands
<CR> repeat the last command
BRD hh try Baud Rate Divisor hh
BRT hh set Baud Rate Timeout
D set all to Defaults
E0, E1 Echo off, or on*
FE Forget Events
I print the version ID
L0, L1 Linefeeds off, or on
LP go to Low Power mode
M0, M1 Memory off, or on
RD Read the stored Data
SD hh Save Data byte hh
WS Warm Start (quick software reset)
Z reset all
@1 display the device description
@2 display the device identifier
@3 cccccccccccc store the @2 identifier
Programmable Parameter Commands
PP xx OFF disable Prog Parameter xx
PP FF OFF all Prog Parameters disabled
PP xx ON enable Prog Parameter xx
PP FF ON all Prog Parameters enabled
PP xx SV yy for PP xx, Set the Value to yy
PPS print a PP Summary
Voltage Reading Commands
CV dddd Calibrate the Voltage to dd.dd volts
CV 0000 restore CV value to factory setting
RV Read the input Voltage
Other
IGN read the IgnMon input level
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elm 327 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elm 327 in the language / languages: English as an attachment in your email.

The manual is 0,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info