Manual Elm 327 (page 4 of 94) (English)

612699

Zoom out

Zoom in

1/94

ELM327

Elm Electronics – Circuits for the Hobbyist

www.elmelectronics.com

Pin Descriptions

4 of 94

MCLR (pin 1)

A momentary (>2µsec) logic low applied to this input

will reset the ELM327. If unused, this pin should be

connected to a logic high (VDD) level.

Vmeasure (pin 2)

This analog input is used to measure a 0 to 5V

signal that is applied to it. Care must be taken to

prevent the voltage from going outside of the supply

levels of the ELM327, or damage may occur. If it is

not used, this pin should be tied to either VDD or VSS.

J1850 Volts (pin 3)

This output can be used to control a voltage supply

for the J1850 Bus+ output. The pin normally outputs

a logic high level when a nominal 8V is required (for

J1850 VPW), and a low level for 5V (for J1850

PWM), but this can be changed with PP 12. If this

switching capability is not required for your

application, this output can be left open-circuited.

J1850 Bus+ (pin 4)

This active high output is used to drive the

J1850 Bus+ Line to an active level. Note that this

signal does not have to be used for the Bus- Line (as

was the case for the ELM320), since a separate

J1850 Bus- drive output is provided on pin 14.

Memory (pin 5)

This input controls the default state of the memory

option. If this pin is at a high level during power-up or

reset, the memory function will be enabled by

default. If it is at a low level, then the default will be

to have it disabled. Memory can always be enabled

or disabled with the AT M1 and AT M0 commands.

Baud Rate (pin 6)

This input controls the baud rate of the RS232

interface. If it is at a high level during power-up or

reset, the baud rate will be set to 38400 (or the rate

that has been set by PP 0C). If at a low level, the

baud rate will be initialized to 9600 bps.

LFmode (pin 7)

This input is used to select the default linefeed mode

to be used after a power-up or system reset. If it is at

a high level, then by default messages sent by the

ELM327 will be terminated with both a carriage

return and a linefeed character. If it is at a low level,

lines will be terminated by a carriage return only.

This behaviour can always be modified by issuing an

AT L1 or AT L0 command.

VSS (pin 8)

Circuit common must be connected to this pin.

XT1 (pin 9) and XT2 (pin 10)

A 4.000 MHz oscillator crystal is connected between

these two pins. Loading capacitors as required by

the crystal (typically 27pF each) will also need to be

connected between each of these pins and circuit

common (Vss).

Note that this device has not been configured for

operation with an external oscillator – it expects a

crystal to be connected to these pins. Use of an

external clock source is not recommended. Also,

note that this oscillator is turned off when in the Low

Power or ‘standby’ mode of operation.

VPW In (pin 11)

This is the active high input for the J1850 VPW data

signal. When at rest (bus recessive) this pin should

be at a low logic level. This input has Schmitt trigger

wave shaping, so no special amplification is

required.

ISO In (pin 12)

This is the active low input for the ISO 9141 and

ISO 14230 data signal. It is derived from the K Line,

and should be at a high logic level when at rest (bus

recessive). No special amplification is required, as

this input has Schmitt trigger wave shaping.

PWM In (pin 13)

This is the active low input for the J1850 PWM data

signal. It should normally be at a high level when at

rest (ie. bus recessive). This input has Schmitt

trigger wave shaping, so no special amplification is

required.

J1850 Bus- (pin 14)

This active high output is used to drive the J1850

Bus- Line to an active (dominant) level for J1850

PWM applications. If unused, this output can be left

open-circuited.

ELM327DSJ

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elm 327 in the language / languages: English as an attachment in your email.

The manual is 0,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elm 327 Manual

Product: