741480
2
Zoom out
Zoom in
Previous page
1/2
Next page
SPA10 - BRACKET FOR IRA/IMA SERIES DETECTORS
SPA10 - GELENKSTÜCK FÜR IRA/IMA BEWEGUNGSMELDER
WALL FASTENING / WANDMONTAGE
Horizontal traverse: ± 42°
Vertical traverse: – 86° ÷ +15°
Horizontale Schwenkung: ±42°
Vertikale Schwenkung: -86° ÷ +15°
CEILING FASTENING /
DECKENMONTAGE
Horizontal traverse: ± 42°
Vertical traverse: – 11° ÷ +92°
Horizontale Schwenkung: ±42°
Vertikale Schwenkung: -11 ÷ +92°
L’utilizzo della vite a corredo
assicura il corretto blocca
gg
io
del fondo del rivelatore allo
snodo, in conformità alle
norme CEI 79.2.
L’utilisation de la vis
de fermeture est
indispensable pour
assurer le correct
blocage de la rotule.
Attenzione: la vite di
blocco del movimento
va inserita nella sede
più distante rispetto
al dado di serraggio.
Attention : la vis de blocage
du mouvement doit être
placée dans le perçage le
plus distant par rapport a
l’écrou de serrage.
ENGLISH
DEUTSCH
INSTALLATION
Open the special knock-down provision and assemble the
bracket as illustrated in the figure. Put in the cable
(diameter: max. 6 mm) through the bracket hole, then
fasten it to the wall or ceiling by making use of two dowels.
After the most advantageous position to the covering area
requirements has been identified, the nut should be
tightened down to 1 to 1.5 Nm by means of a wrench (size:
15), then the detector cover should be closed.
SPA10 TAMPER KIT INSTALLATION
Place the tamper at the bracket rear, as illustrated in the
figure. Allow the two wires to pass through the bracket hole,
and then connect them in series to the anti-tampering line.
CAUTION! The correct installation for tamper kit is the
following:
1) remove the spring from the tamper;
2) place a dowel (not supplied) onto the wall, then
adjust the screw so that the tamper can be pressed
when the bracket is present;
3) fasten the bracket to the wall.
INSTALLATION
Den vorbereiteten Durchbruch öffnen und das Gelenk, wie
abgebildet, zusammenbauen.
Das Kabel (Durchmesser max. 6 mm ) durch die
Gelenköffnung ziehen und mit zwei Dübeln an der Wand
oder Decke befestigen. Nachdem der geeignete Platz zur
Absicherung des Bereichs ermittelt wurde, ist die Mutter
mit einem 15-Schlüssel fest anzuziehen, mit
Anzugsmoment zwischen 1 und 1,5 Nm; zuletzt dann den
Deckel des Sensors schliessen.
TAMPER KIT SPA10 INSTALLATION
Den tamper, wie abgebildet, an der Rückwand des
Gelenks einbetten. Die beiden Drähte durch den
Durchbruch im Gelenk ziehen und diese in Reihe zur
Sabotageleitung schalten.
ACHTUNG! die korrekte Installation des tamper kit für
den Entfernungsschutz ist das folgende:
1) Feder vom tamper entfernen;
2) An der Wand einen Dübel (nicht lieferte) vorbereiten
und die Schraube so einregulieren dass, bei
vorhandenem Gelenk, der tamper angepresst wird;
3) Gelenkstück an der Wand befestigen.
KIT TAMPER SPA10
SPA 10 TAMPER KIT
V
ITE
/
VIS
ELKRON S.p.A.
Via Cimarosa, 39 – 10154 Torino (TO) – ITALY
Tel. +39(0)113986711 – FAX +39(0)113986790
www.elkron.it mal to: info@elkron.it
DS80IR75-001_LBT80145
IS1190-AB
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron SPA10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron SPA10 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info