741401
6
Zoom out
Zoom in
Previous page
1/18
Next page
6 DS80TC2S-001
10
ENGLISH
The IR600FC/N is a passive infrared motion sensor (PIR) with built-in camera. When motion is detect, it sends alarm signals and
high-quality images to the system control unit.
The detector has a detection range of 12 metres when it is mounted at 2 metres from the ground. The detector consists of two
parts, a cover and a base. The cover contains all the electronic and optical components and the camera, while the base is used for
fixing. The base has arrangements for holes for installation on a flat surface and holes for fixing to the corner bracket (included).
The detector is also provided with a single tamper switch which is activated when an attempt to open the cover or detach it from
the wall.
Part identification
1. Illuminator
The illuminator provides sufficient light to acquire images in poor lighting conditions.
The blue LED and the illuminator both blink once when the function button is pressed for 10 seconds to
indicate that the detector was reset.
2. Blue LED/Function button
Meaning of the LEDs:
The blue LED lights up in the following conditions:
- The blue LED blinks once every 20 minutes: the detector has lost the connection with the control
unit.
- The blue LED lights up for 30 seconds: the detector is being initialised in test mode.
- The blue LED blinks fast twice: the detector is connected correctly to the control unit.
- The blue LED lights up for two seconds during normal operation: the detector has detected a
motion.
- The blue LED blinks fast: the detector is transmitting images to the control unit.
- The blue LED and the illuminator blink once: the detector was reset.
Using the function button:
- Press the button once to send a supervision signal.
- To reset the detector: hold the button pressed for 10 seconds. Release the button when the
illuminator and the blue LED blink once.
- For the learning procedure of the detector on the control unit
3. IR sensor lens
The sensor is used to detect the movements of people and/or animals by detecting their body
temperature.
4. Camera
lens
5. Battery compartment lid
6. Tamper switch
The tamper switch is activated if the detector is detached from the wall or from the corner bracket
or if the cover is opened.
7. Battery compartment
8. Jumper JP3 PIR sensitivity
- Jumper on: "High" sensitivity level.
- Jumper off: "Normal" sensitivity level (default setting).
9. Jumper JP2
- Jumper On: after transmitting following a detected movement, the signals and the acquired
images will be transmitted if any other movements are detected (default setting).
- Jumper Off: the detector has a “sleep time” (see below) of approximately 1 minute to save
energy.
10. Fastening screw
Jumper On
The jumper is
connected between
the two pins.
Jumper Off
the jumper is removed
or "arranged" on a pin.
Jumper
On
The jumper is connected
between the two pins.
Jumper Off
the jumper is removed
or "arranged" on a pin.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron IR600FC-N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron IR600FC-N in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron IR600FC-N

Elkron IR600FC-N Quick start guide - English, German, French, Italian - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info