741419
6
Zoom out
Zoom in
Previous page
1/12
Next page
6 DS80IR2E-001B
see the instruction manual of the control unit to complete the learning procedure.
Proceed with the installation after having ascertained that the detector is working in the desired position.
Mounting method
The detector was designed to be mounted on a flat surface or in a corner using the fixing screws and the anchor bolts provided.
Hole arrangements are provided on the base where the plastic is thinner and may be broken for mounting. The two hole
arrangements are used to fix on a surface, while the four hole arrangements are used for fixing in a corner, as shown in the following
figure.
Surface mounting
I. Remove the fixing screws and the cover.
II. Perforate the appropriate hole arrangements on the inner side of the
base.
III. Using the template for the holes, make the holes in the surface.
IV. Insert the anchor bolts if the device is fixed to plaster or bricks.
V. Screw the base into the anchor bolts.
VI. Screw the cover onto the base.
Corner mounting:
I. Perforate the four arrangements for corner holes.
II. Using a template for the holes, make the holes in the corner.
III. Insert the anchor bolts.
IV. Screw the base into the anchor bolt.
V. Screw the cover onto the base.
Installation
Choose the position of the detector, i.e. either in a corner or on a
surface.
After having selected the installation position, follow the procedure
described above to mount the detector.
Press the Test button to enter Test mode. Move in the protected area
and observe when the LED lights up to check that the detection
coverage is adequate.
Installation is complete when the detection coverage is appropriate.
Installation advice
The detector was designed to operate with a detection range of 12 metres when it is mounted at 2 metres from the ground.Take the
following guidelines into consideration to optimise detector use.
It is advised to install the detector in the following positions:
Mount the detector at a height of 1.9-2.0 metres to optimise performance:
Mount in a place were pets cannot access the detection area.
Mount it in a position in which an intruder would normally cross the field of vision of the detector from one side to the other.
Mount it in a corner to have the widest view possible.
Mount it where the field of vision is not obstructed, e.g. by curtains, ornaments etc.
Restrictions
Do not position the detector directly facing a door protected by the door contact because the wireless signals of the door contact
and of the detector could be transmitted in input at the same time, causing the signals to cancel each other out.
Do not install the detector fully exposed to direct sunlight.
Do not install the detector in areas in which devices which could cause sudden changes of temperature in the detection area
are present, such as air conditioning units, radiators etc.
Avoid large size obstacles in the detection area.
Do not point directly towards source of heat, such as fires or boilers, and do not install over radiators.
Avoid moving objects in the detection area, i.e. curtains, soft furnishings etc.
Technical specifications
Power supply: 1 battery CR123A 3V
Battery life: 5 years (typical value, may vary according to use)
Two-way radio frequency: 868 MHz
Infrared range: max 12 m with 110° angle
Working temperature range -10°C – +45°C
Dimensions: 53.2mm X 67mm X 89.2mm
Weight: 300g
Compliant under EN 50131 Grade 2, Class
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, URMET S.p.A. declares that the radio equipment type: INFRARED DETECTOR IR600 is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.elkron.com
ELKRON
Tel. +39 011.3986711 - Fax +39 011.3986703
www.elkron.com mail to: info@elkron.it
ELKRON
is a trademark of URMET S.p.A. Via Bologna 188/C –
10154 Torino (TO) Italy
HU
www.urmet.com
U
H
Coverage diagram
Hole arrangements for
corner fixing x 4
Hole
arrangements for
fixing on surface
x 2 (inner)
MADE IN TAIWAN
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron IR600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron IR600 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron IR600

Elkron IR600 Quick start guide - English, German, French, Italian - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info