741436

Elkron IM600 Manual

5
Zoom out
Zoom in
Previous page
1/16
Next page
DS80IM39-001B 5
ENGLISH
The IM600 detector implements infrared (PIR) and microwave (MW) motion detection technology. The combination of the two
detection methods considerably reduces the false alarm rate, employing PIR for initial detection and microwaves for confirmation
before sending the alarm signal.
Part identification
1. Transmitter LED (red)
The LED indicator blinks to indicate that signals are being transmitted in the following
situations.
- The Learn/Test button is pressed.
- The tamper switch is actuated or reset.
- Motion is detected in Test mode.
- Motion is detected in flat battery or open tamper conditions during normal operation.
The LED does not blink if the tamper switch is closed, the battery is charged and the detector is
not in Test mode.
The LED blinks to indicate signal transmission, blinking rapidly twice upon receiving confirmation
from the panel.
The LED will blink every 4 seconds when the battery of the detector is flat.
2. Microwave detector LED (blue)
The LED lights up briefly when the microwave detector is in Test or in Microwave Test
mode.
3. IR detection LED (green)
The LED lights up briefly when the microwave detector is in IR Test mode.
4. Learn/Test button
5. Lens
6. Battery housing
7. Supervision jumper
Jumper not fitted Supervision is always enabled.
8. Microwave test on/off jumper (JP3)
- When the jumper is set to ON, the detector is in microwave Test mode (see
Microwave test mode).
- When the jumper is set to OFF, microwave Test mode is deactivated. (default)
9. Tamper switch
The tamper switch is activated when it is lifted and reset when it is compressed (against a
wall or a surface).
10. Microwave range trimmer
The range is indicated on the right, with the arrow pointing to the set sensitivity level:
- Turned clockwise it increases the detection range (up to 20 metres)
- Turned anticlockwise it decreases the detection range (to a minimum of 3-5 metres)
- Default value: set to a medium value, approximately 10 metres.
11. Tamper hole
The tamper switch must protrude from the hole on the rear cover
12. Pre-cut area
Features
Motion detection
The detector has an integrated PIR sensor and a microwave section. Motion is detected by the PIR sensor during normal
operation. When the PIR sensor detects movements, microwave detection is activated to verify the detected motion. If
both the PIR and the microwave confirm motion detection, the detector transmits the alarm signal.
Set the microwave range trimming to adjust the detection range.
When the trimmer is set to maximum, the detector has an approximately range of 12 metres and mounted at a height of
1.9~2 m.
When the trimmer is set to minimum, the detector has an approximately range of 5 metres and mounted at a height of
1.9~2 m.
Sleep Time
The detector has a “sleep time” of approximately 1 minute to save energy. After having transmitted a detected movement,
the detector will not transmit again for 1 minute; any further movements detected during the sleep period will extend the sleep
period by another minute. In this way, continuous movements in front a detector will not drain the battery unnecessarily.
Test mode
The detector can be set to Test mode by pressing the specific Learn/Test button. Test mode lasts for 3 minutes and restarts
from 3 minutes whenever the Learn/Test button is pressed. In Test mode, the sleep timer is deactivated and the LEDs light up
when the detector detects a movement to notify the user.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron IM600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron IM600 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info