741427
5
Zoom out
Zoom in
Previous page
1/12
Next page
Learning of the detector by the control unit
The detector must be learnt by the control unit to transmit the signal if motion is detected. Proceed as follows to perform the
device learning procedure.
The detector may be learnt by the control unit only within three minutes from switch-on.
1. Remove the sun visor fastening screws to remove this component.
2. Remove the battery compartment cover to open the battery compartment and the dip switches.
3. If necessary, configure the dip switches; for information on setting, see the table provided above.
4. Insert the two lithium batteries “AA” L91 in the battery compartment, taking care to observe the polarity.
5. Make sure that the Tamper switch is open (released) before proceeding to the next step.
6. Within three minutes from switch-on, hold the function button pressed for 10 seconds and then release it when the red
LED and the illuminator blink once. Make sure that the learn function has been activated on the control unit.
7. After having been leant by the control unit, the detector is automatically recorded in the system. Check the control unit
to check that the learning and registration procedure were performed correctly.
8. Once learnt by the control unit, if the detector connection is lost, the LED will blink for 20 minutes to signal the fault.
Test mode
The Test mode is used to control the detection coverage of the device not the communication range with the control unit.
To access test mode, hold the function button pressed for a few seconds then release it to start the test mode that lasts for three
minutes.
The detector will start initialisation during the first 30 seconds. It is advisable not to generate alarms during this time.
Motion detection in front of the detector can be checked at the end of the initialisation period. The red LED lights up for two
seconds after detection.
Mounting and installation method
The detector was designed to be mounted on a flat surface or in a corner by means of the fixing screws and the anchor bolts
provided.
The package contains a metal rotation bracket to allow adjusting the camera and sensor angle. The bracket is
provided with holes for fixing to a wall or in a corner.
1. Use the installation holes on the rotation bracket to mark the corresponding points on the wall or in a corner; if
necessary, insert the anchor bolts into the wall.
2. Screw the rotation bracket in the marked installation points.
3. Screw the bracket arm onto the detector (Figure 1).
4. Clip on the detector onto the rotation bracket and adjust the detector angle with the upper holes of the bracket
(Figure 2).
5. Fix the detector onto the bracket by tightening the upper screw (Figure 3).
Figure 1 Figure 2 Figure 3
Camera
installation
Corner installation
holes
Camera angle selection
Corner installation holes
Installation
holes in wall
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron EIR600FC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron EIR600FC in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron EIR600FC

Elkron EIR600FC User Manual - English, German, French, Italian - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info