741426

Elkron EIR600 Manual

4
Zoom out
Zoom in
Previous page
1/12
Next page
DIP Sensitivity level
Switch5 Switch6
ON ON Low; for 75 cm / 60 kg animals
ON
OFF
position
Medium; for 60 cm / 40 kg animals
OFF
position
ON High; for 45 cm / 30 kg animals
OFF
position
OFF
position
Higher; for 30 cm / 20 kg animals
(default)
DIP Position Function
Switch7
ON Double detection on (default)
OFF
Double detection off
Switch8
ON
Reserved
OFF
DIP Position Function
Switch1
ON Test mode
OFF
Normal mode (default)
Switch2
ON Supervision off
OFF
Supervision on (default)
Switch3
ON
Detector facing a closed space (eg a wall higher
than a person within 10 m of the detector)
OFF
Detector facing an open space (no wall within
10 m of the detector) (default)
Switch4
ON
Detector facing a surface that does not easily
release heat (eg a lawn) (default)
OFF
position
Detector facing a surface that easily releases
heat (eg in cement, or stone or tiled)
ENGLISH
EIR600
OUTDOOR IR DETECTOR WITH PET FUNCTION
1. Test button and LED
2. Double sensor
3. Battery housing for two AA 3.6 V lithium batteries.
4. Tamper switch
5. DIP Switch block
6. Bracket arm
7. Rotating bracket
LED
In normal operating mode, the LED indicator blinks to indicate that signals are being transmitted in the following situations.
When movement is detected in flat battery conditions.
When the cover is opened and the tamper switch is actuated.
When movement detected if the tamper alarm condition persists.
When motion is detected in Test mode.
When the Test button is pressed in tampering conditions or if the battery of the device is flat.
The LED does not blink if the tamper switch is closed, the battery is charged and the detector is not in Test mode.
The LED blinks to indicate signal transmission, blinking rapidly twice upon receiving confirmation from the control unit.
DIP Switch position table
The function of each DIP Switch is listed in the following table. The DIP Switch is in position ON or OFF. Position up indicates
ON, position down indicates OFF.
Preparation – Learning of the detector by the control unit
Loosen the screws and remove the cover.
Set the sensitive switch as needed as shown in the DIP Switch position table.
Insert two AA 3.6 V lithium batteries in the battery housing ensuring that the polarity is correctly connected.
The LED indicator will blink for 30 seconds. The detector is being initialised. During initialisation, the detector will not be
active. It is advisable not to generate any alarms during this time. Once the initialisation time has finished, the LED will
switch off and the detector is ready to start working.
Set the control unit to learning mode; see the instruction manual of the control unit for details.
Hold the Test button on the front cover pressed for about 3 seconds.
The corresponding information is displayed if the control unit receives the signal. Refer to the instruction manual of the
control unit to complete the learning process.
Put the control unit in Walk Test mode (motion Test) after the detector learning procedure. Hold the detector in the
required position, press the Test button to check that the concerned position is within the communication coverage range.
Proceed with the installation after having ascertained that the detector is working in the desired position.
Test mode
The detector can be set to Test mode for three minutes by pressing the Test button once. In Test mode, the sleep time is off
and the LED indicator lights up for two seconds, independently from motion detection. The detector automatically exits Test
QUICK GUIDE
DS80IR2F-002
Coverage diagram
Installation height / Range
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron EIR600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron EIR600 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info