741399
8
Zoom out
Zoom in
Previous page
1/24
Next page
8 DS80IM41-001B
Sensitivity Function (Increase of Sensitivity)
NORMAL: Dip Switch N°1 in OFF position (Default). Recommended for most exterior installations.
HIGH: Dip Switch N°1 in ON position. Recommended when a higher detection speed is required.
Trimmer (sensor capacity)
This regulates the sensor capacity (turning the trimmer clockwise increases the detector capacity). To adjust it, keep in mind the
operating area determined by the microwave. The sensor will automatically adapt the functioning of the infra-red with this
regulation. The trimmer default position is completely clockwise turned.
<NOTE>
Unlike the microwave, for which it is possible to establish its detector limit with sufficient precision, this condition is not
applicable for the infra-red. The reason is because the detection of the infra-red is conditioned by the ambient temperature,
by the intruder’s clothing, by the absence/presence of wind, etc. The trimmer therefore automatically regulates the infra-red
detection capacity in function of the capacity of the microwave selected without necessarily defining its operating area as that
of the microwave itself (the infra-red will be configured for the most unfavourable conditions at that capacity).
Detector LED indicator
Dip Switch N° 3 in OFF position
In the normal operating mode, the LED indicator blinks to indicate the transmission of the signal in the following situations:
When it is powered, it blinks for 60 seconds (initialisation phase).
When the cover is open and the tamper switch is activated, for 4 minutes (test mode).
During the test mode for every movement detected
If the tamper is open, for every movement detected.
It does not blink if a movement is detected in normal mode and with the tamper closed.
Dip Switch N°3 in ON position (Default)
The LED also blinks when a movement is detected in normal operating mode and with the tamper closed, at the cost of depleting
the battery. It is inhibited as soon as the cut-off time starts.
Battery
The detector is powered by a CR2 3V lithium battery provided in the package. The detector is capable of detecting the flat
battery status, sending a signal to the control unit together with the normal transmission of signals so that the control unit
displays the corresponding status.
<NOTE>
During the replacement of the battery, after having removed the dead battery, press the tamper twice to completely
discharge the device before inserting the new battery.
To check that it is functioning correctly, conduct the Walk Test for the radio signal level capacity by pressing the
learning button, button 11 (see the control unit instruction manual).
Detector learning
To open the sensor, lift the LED filter screw covers and loosen the closure
screws beneath it. Loosen the screws that hold the card in place without
unscrewing them completely and disassemble the electronic card, lifting it
upward first to release it from the screw, as illustrated here.
Insert the CR2 battery into the battery compartment, taking care to
observe the polarity.
When the detector LED indicator is powered, it blinks for 60 seconds
(initialisation phase). The detector is not yet activated.
Enable the control unit for the learning device. For details, see the
control unit instruction manual.
Press the learning button on the radio circuit and complete the learning
process (see the control unit instruction manual).
Put the control unit in Radio Device Testmode after the detector
learning procedure.
Insert the circuit on the bottom, tighten the screws and close the front
panel, positioning the detector in the where it is to be installed.
Once the radio cover is checked, it is possible to reopen the front panel, disassemble the circuit and attach the detector
directly onto the wall or using the bracket and optional articulation.
Tighten the closure screws.
Apply the LED filter screw covers.
Installation on flat surfaces
The detector was designed to be assembled on a flat surface, using the fastening screws and the anchor bolts provided.
The base is marked where the plastic is thinner for boring holes suitable for installation.
I. Cut seat A and seat B on the bottom (see the image below).
II. Using the holes template, make holes on the surface.
Card screw
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elkron DT600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elkron DT600 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elkron DT600

Elkron DT600 Quick start guide - English, German, French, Italian - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info