Manual Elite Nero (page 32 of 105) (Danish, Swedish, Norwegian, Finnish)

782462

Zoom out

Zoom in

1/105

power the trainer making the wheel move (even manually)

or pedalling a few times, for a few seconds. In fact, on

start-up, if the speed exceeds zero, Nero resets the sensor

saved in the memory and starts looking for another sensor,

as if it were the first time.

When the Nero resets the serial number of the power

sensor, it performs 6 slight vibrations to confirm the

cancellation.

NOTES:

- If Nero has connected to an incorrect sensor, just reset

the coupled sensor and repeat the coupling operation,

paying attention to move the sensor you do not want Nero

to connect to, away.

- If, during training, Nero loses the connection with the

power sensor, it goes automatically to using the formulas

to calculate the power. In the meantime, it keeps trying to

re-connect with the sensor.

- The trainer looks for ANT+ sensors first and Bluetooth

afterwards. If the power sensor is both ANT+ and

Bluetooth, very likely the trainer will latch on to the ANT+

signal.

- The cancellation vibrations are very light. To feel them, it

may be necessary to lay your hand on the resistance unit.

- In case of Bluetooth pedals / cranks, the trainer latches

onto just one of the two. In this case, it is not possible to

pre-determine which pedal / crank it will latch onto.

Moreover, since in this case each pedal / crank measures

the power developed by the relative leg, the value sent is

about half the total power developed by the cyclist.

In this case, you must enable the "half power" option with

the My E-Training app to use it properly (Parameter -

advanced configuration - Virtual Power Sensor ).

06_NOTES ON POWER VALUE ACCURACY

Power data sent by Nero results from a large number of

calculations. These are obtained by mainly taking into

account pedaling speed, braking power of the rollers and

other factors.

Elite calibrates every single Nero in order to improve accuracy,

with the aim of reducing errors as much as possible, though

there are some factors that you need to consider while

training that might influence power data accuracy.

First off, we suggest calibrating with Spindown.

After you’ve done it once, it is advisable to do it every time

after one of these events:

- After changing wheels

- After changing the bike

- After every significant variation in tyre pressure.

- After every significant variation in rider’s weight or when

there’s a different rider altogether

Spindown eliminates resistance variations due to one of the

aforementioned events - it measures all of these components

and makes the home trainer more accurate.

Here are some more suggestions on how to optimize power

data accuracy:

- Maintain a constant position on the bike. Indeed, the center

of gravity changes every time you change position on the

bike, consequently weight distribution on the home trainer

changes too, resulting in a variation of resistance.

- Fold up the home trainer once you’re done training,

otherwise the elastic bands might deform, thus changing the

overall home trainer resistance.

If the home trainer connects to a bike’s power meter

(where available), the aforementioned notes are not to be

considered, as power data isn’t calculated but measured by

the sensor on the bike.

Please read the “Power Meter Link (PML)” section for more

info.

07_POWER SENSOR CALIBRATION

Nero can calibrate the internal power measurement system,

which clears the system settings in order to always obtain

accurate power values.

Home trainer should not be heated when you begin the

calibration procedure, so please make sure that it hasn’t

been used in the last 2 hours and it’s been folded up,

otherwise results might be less accurate.

Tap the related command on the My E-Training app and

follow the instructions to launch the procedure.

The calibration command in the mobile version can be found

in Parameters – Advanced Configuration – Home trainer

calibration, while in the desktop version it can be found in

Settings – Home trainer calibration.

This is accomplished by pedalling and increasing speed until

you reach a certain indicated value.

Remember to stop pedalling at the system prompt.

After a few seconds the system will indicate that the

calibration process was successful.

This value is then stored in the Nero’s memory, and accurate

power data will be received from every connected device,

including non-Elite third party software / app / devices.

Please note: the aforementioned calibration procedure can

be conducted with software / app / devices other than the

Elite ones.

Notes on the correct calibration procedure:

- When you're required to stop pedaling, try and maintain

your bike as centered as possible.

- Never lean on walls or other leaning points.

- Keep your feet on the pedals until the procedure is

complete.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elite Nero in the language / languages: Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 4.55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elite Nero Manual

Product: