782459
19
Zoom out
Zoom in
Previous page
1/127
Next page
23
CN
1个后下叉右侧接合器,
长度=142mm(5.6英寸) (参考编号E)
1个后下叉左侧接合器,
长度=142mm(5.6英寸) (参考编号F)
1个电源适配器 (参考编号G)
1个快速释放 (参考编号I)
1个左侧支撑 (参考编号L)
1个右侧支撑 (参考编号R)
1个中心支撑 (参考编号O)
2个TBEIM6x60螺丝 (参考编号P)
6个M6垫圈 (参考编号Q)
2个M6螺母 (参考编号S)
2个TBEIM8x35螺丝 (参考编号T)
󶳧󸃓
-拆卸DrivoII本体(参考A)
-按照(图1)所示垂直放置Drivo II本体(参
考A),并使用上部把手将其固定到位
- 展开支腿,直至听到安全操纵杆发出咔嗒声
(图2和图3)。
-将滚轴放平,插入侧支撑(参考编号L及R)(图4).
- 使用垫片及M8螺母将M8x60固定,直到可蹭
到侧支撑,从而使其能旋转(P-Q-S)(图5).
- 最大程度地展开侧柱条(图6)
-中心轴必须与支架上的孔对齐。(图7)
- 紧固安全旋钮(图8)。
-插入中心支撑(参考编号O)(图9)
-拧紧螺丝和M8垫片(参考编号T-Q)(图10)
- 确保家用训练器保持平稳(图 11),否则请
调节可调支脚(图12A-12B)。
-注意!中心支撑须距离地面3mm(图13)
󲶽󸃓󱻳󳑎󹴘󸱑󱳬󸵳󱛖
󲃅󱿿󱾘󷼀󴪂
󹠣󸦤
-对齐槽型,将卡式飞轮组装到塔基。
Shimano®/SRAM®9速飞轮盘(图14)需要2个垫
片(参考编号B),而10速飞轮盘(图15)需要1个
垫片,11速飞轮盘(图16)无需垫片。根据所使
用飞轮盘品牌,可能与上述特征存在差异。
- 使用扭矩扳手将卡式飞轮随附的锁定环拧到
塔基本体上(图17)。
小心!
严格按照卡式飞轮制造商提供的有关具体安装
技术的说明,并需要额外的垫片和扭矩规格。
注:如果您有疑问或无法安装卡式飞轮,请联
系您的经销商。本保修不含自行车和/或 Drivo
II因安装不正确而发生的任何损坏。
-DrivoII随附直径为5mm的快拆垫片,用于间
隔为130mm(5.1in.)到135mm(5.3in.)的
勾爪。因此,在勾爪间隔为 130-135mm(5.1-
5.3 in.)的自行车上,插入左勾爪接头(参考
D)(图18)。对于直径 12mm (0.47 in.)x
142mm(5.6in.)的筒轴自行车,请查阅第15
页的段落。
󲶽󸃓
- 松开自行车的后制动并将链条放到最小后链
轮和最大前链环处。从后轮上拆下快拆。
- 将快拆和勾爪接头(参考 C)插入到卡式飞
轮上(图19)。
- 将自行车链条放到DrivoII的最小飞轮(图20
)上。
- 按照自行车的类型将自行车的后勾爪完全装
到 Drivo II 的卡式飞轮(图21)上,注意内外
位置是否正确:
- 公路和计时赛自行车(130 mm 三角形)用
外部三角形接头(参考C)(图22)。
- 山地自行车(135mm三角形)(图23)用内
部三角形接头(参考C)。
注:三角形接头(参考C)的滚花侧必须正对
着自行车勾爪。
将自行车稳固安装在DrivoII上,并紧固合上快
拆杆。所产生的压力应可将自行车后叉端锁定
在DrivoII上。
󲺼󱻳󳑎󹴘󸱑󲶽󸃓󱳬󸵳󱛖
󱿿󱾘󷼀󴪂󹠣󸦤
- 对于配有筒轴的自行车,需要更换轴中的套
筒组:
1)如果已插入,则拆下左接头(参考 D)并拧
下用于130-135mm链叉(图24)的右接头;
2)将右接头拧到末端(参考 E)并插入用于
142mm链叉(图25)的左接头(参考F)。
3)使用17mm扳手(11/16in.)以5Nm紧固
扭矩(44in-lbs)安装垫片(参考E)。使用中
等强度的容油性螺纹胶将螺母锁到轴上。
4)松开自行车的后制动并将链条放到后轮的最
小链轮以及前链环处。从后轮上拆下筒轴。
5)将自行车的后勾爪放到 Drivo II 的卡式飞轮
轴上。
6)将筒轴插到DrivoII链轮卡式飞轮轴上。
7)确保自行车安全放置到 Drivo II 上并通过猛
推筒轴, 压力应使自行车车叉勾爪保持锁定到
DrivoII结构上。
通过推拉车架和车座的顶管,确保自行车稳
定。如果自行车在DrivoII上仍有轻微移动,则
用更大功率锁定筒轴。
- 开始蹬踏。先骑得很慢,然后逐渐增加您的
速度,直到您熟悉DrivoII的功能
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elite Drivo II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elite Drivo II in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 4.11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info