Manual Elite Direto XR-T (page 35 of 128) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

782409

Zoom out

Zoom in

1/128

the quick release. The resulting pressure should keep the

bicycle dropouts locked to the DIRETO XR-T.

- Make sure the bike is perfectly vertical once installed.

WARNING: the dropout of the bicycle must be leaning on

the edges of the adapter and not on the Quick Release.

Elite shall not be liable for any damages that might

arise from an improper assembly of the bicycle on the

hometrainer.

17_INSTALLING THE DIRETO XR-T

ON BICYCLES WITH Ø12 L=142 MM

CHAINSTAYS

1) Insert the left adapter (Ref. G) and screw the rigth

adapter (Ref F) for 142mm carriages (Fig. 16);

2) Loosen the rear bicycle brake if necessary.

3) place the chain on the smallest sprocket and chainring;

4) remove the thru-axle from the rear wheel.

5) remove the rear wheel from the bicycle.

6) position the bicycle by inserting the chain on the smallest

sprocket.

7) fully insert the rear dropouts of the bicycle on the edge

of the DIRETO XR-T sprocket set axle.

8) Insert the thru-axle on the DIRETO XR-T sprocket set

axle hole;

9) Make sure the bicycle is safely positioned on the DIRETO

XR-T and lock the thru-axle with a strong push. The

pressure should make the bike dropouts remain locked

onto the structure of the DIRETO XR-T.

10) Make sure the bike is stable by pushing and pulling the

top tube of the frame and the saddle. Should the bike still

be moving a little on the DIRETO XR-T, use more force to

lock the thru-axle.

If you wish for more bicycle stability it's advisable to use

the provided Riser block (Ref I) to be placed under the front

wheel.

Start pedalling. Ride very slowly at ﬁrst and increase your

speed gradually until you become familiar with the features

of DIRETO XR-T.

18_POWER SUPPLY

- DIRETO XR-T has an electronic motherboard that is

powered via a standard power supply adapter (included).

- Connect the power supply to the grid and the jack to the

proper connector on the back of the DIRETO XR-T. A small

vibration indicates that the system is booting up to its initial

position. This operation might last up to 15 seconds.

Hang the power supply cable on the dedicated hanger (Pics

17 and 18).

The DIRETO XR-T compliance with EU laws (see

“Declaration of conformity”, page 102) may be voided if a

charger different from the original is used.

19_REMOVING THE BICYCLE

- Shift the bicycle chain on the smallest cassette sprocket

of DIRETO XR-T and of the smallest front chainring of the

bicycle.

- Open up the quick release (or remove the thru-axle) and

remove the bicycle from the DIRETO XR-T.

- To avoid clutter or for transportation: loosen the knobs

(Pic. 19) and fold the side legs (Pic. 20 - 21).

WARNING: adapters ref. C, D, E, F, G are small sized

components and might easily be misplaced or lost. If you

move the hometrainer it's advisable to remove the adapters

and store them in their bag as they might easily slip out

during transport.

Any spare parts are available in our online store or by

directly contacting Elite and/or your country's distributor.

20_INSTALLATION INSTRUCTIONS FOR FREE-

HUB BODY COMPATIBLE WITH CAMPAGNOLO

9/10/11/12 SPEED SPROCKET CASSETTE,

FREE-HUB BODY COMPATIBLE WITH XD/

XDR SRAM 12 SPEED, FREE-HUB BODY

COMPATIBLE WITH MICRO SPLINE SHIMANO

12 SPEED

- Replace the free-hub body originally present on

the DIRETO XR-T with the accessory compatible with

9/10/11/12 speed CAMPAGNOLO sprocket cassette or

XD/XDR compatible free-hub body (for 12 speed SRAM

sprocket cassette) or Micro Spline compatible free-hub

body (for SHIMANO 12-speed sprocket cassette) following

the following steps:

1) Unscrew the fastening sleeve (Pic. 22).

2) Remove the freehub body from the DIRETO XR-T shaft

(Pic. 23).

3) Fully insert the body compatible with CAMPAGNOLO or

XD/XDR or Micro Spline sprocket cassette. (Pic. 24 and

25).

4) Tighten the fastening sleeve by using a 17mm wrench

with a 5Nm (44in-lbs) tightening torque (Pic. 26).

Only for CAMPAGNOLO compatible body:

- 2 spacers (Ref. B) are usually needed for the 9 speed

cassette (Pic. 5), 1 spacer for the 10 speed cassette (Pic. 6)

and no spacer is required for the 11 and 12 speed cassette

(Pic. 7). Depending on the cassette brand you are using

there might be some differences with the aforementioned

general data.

ATTENTION!

Strictly follow the instructions provided by the cassette

manufacturer with regard to speciﬁc installation techniques,

the need for additional spacers and torque speciﬁcations.

NOTE: Please contact your dealer if you have questions

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elite Direto XR-T in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 8.74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elite Direto XR-T Manual

Product: