Manual Elica Vogue (page 12 of 14) (English)

471230

Zoom out

Zoom in

1/14

Fig. 9

6. Hook the frame onto the 4 screws (see step 4).

CAUTION! The side of the truss with connection box

corresponds to the side of the control panel with hood

assembled.

7. Tighten the 4 screws.

8. Insert and tightly screw in another 4 screws and 2

washers on the safety fastening holes left free.

Note - only for the suction Version: connect the upper

end of the discharge tube to the discharge device toward

the exterior (e.g. hole in the ceiling).

Note- for Filter Version only: insert the extensions on the

deflector F blocking them with 4 total screws (Picture 9F).

Carry out the electrical connection to the mains power supply,

only turn on the power supply upon completion of assembly.

Fig. 10

9. Couple the two sections of the chimney as cover to the

lattice.

Screw the two sections in the lattice with 4 screws (2 on

the front side and 2 on the back side).

10. Definitely fix the two sections with 4 screws M4x7 (2 on

the front side and 2 on the back side).

11. Apply the upper tabs (pressure fastening).

Fig. 11

12. Fit the control shaft in the correct position by pushing it

upwards.

Connect the electricity.

Fig. 12

13. Hook the 4 lower panels (2 on the front side and 2 on the

back side).

Fix the panels to the structure with 2 side screws and 3

central screws, totally 5 screws each panel.

Fig. 13

14. Apply the 4 aesthetic panels as cover to the lower

panels.

Note- To install the panels in the correct position check

the internal notches:

R= Right panel.

L= Left panel.

Fig. 14

15. Mount the upper covers fixing them with 14 total screws

(7 each cover).

Fig. 15

16. Cut 8 pieces (length 10 mm) of adhesive tape "Dual

Lock".

Apply 2 pieces of tape on the stirrups and 2 on the

covers as shown in picture.

17. Definitely fix the upper covers with 2 stirrups and 8

screws (4 each stirrup).

18. Apply the aesthetic covers.

Fig. 16

19. Apply the lower tabs (pressure fastening).

Turn the mains power on again at the central electrical panel

and check for correct hood operation.

Description of the hood

Fig. 1

1. Control panel

2. Grease filter

3. Grease filter release handle

4. Halogen lamp

5. Vapour catcher

6. Telescopic chimney

7. Air outlet (used for filter version only)

8. Panel

Operation

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

The hood is equipped with a “TOUCH” device to control the

lights and speed.

For the correct use please carefully read the intructions below.

Automatic start-up function

The hood is equipped with a temperature sensor which

activates the motor to the first suction speed (power) in the

event that the room temperature in the surrounding area is

higher than 70°C.

The user may switch off or modify the suction speed (power)

(see paragraph “suction speed (power) control”).

Suction speed (power) control

The suction speed (power) is cyclical depending on the speed

sequence “stand-by – 1-2-3-4- Stand by -1-2-...” therefore

every time the T1 button is pressed on the control panel, the

suction speed (power) is increased by one level, in order to

switch off (stand-by) if the button is pressed again when the

hood is in suction speed (power) 4.

The hood may be switched off (stand-by) while the hood is set

on any speed by holding down the T1 button on the control

panel for a bit longer (more than 3 seconds).

The hood's suction speed (power) may be determined as the

control panel is equipped with a LED light that changes colors

as follows, depending on the suction speed (power):

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elica Vogue in the language / languages: English as an attachment in your email.

The manual is 6,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elica Vogue Manual

Product: