133492
6
Zoom out
Zoom in
Previous page
1/7
Next page
Description of the hood
Fig. 1
1. Control panel
2. Grease filter
3. Grease filter release handle
4. Halogen lamp
5. Vapour catcher
6. Telescopic chimney
7. Air outlet (used for filter version only)
Operation
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Control panel
1. Light Button
Press lamp button to turn ON the light on High
Intensity (Lamp state previously OFF).
Press lamp button to turn ON the light on Low
Intensity (Lamp state previously ON).
Press lamp button to turn OFF the light (Lamp state
previously ON).
2. Timer Button
The default timer setting is 10 minutes, and it can be
adjusted between 60 minutes and 1 minute.
After pressing the timer button, the control enters to
a timer setup mode, and user can adjust the timer
countdown time with the “+” and “-” buttons within 5
seconds. The timer can be initiated immediately
pressing the timer button, after setting the timer
duration or pressing the timer button twice (default
10 minutes setting).
If no action occurs within 5 seconds, the countdown
will start.
During the timer setup the “+” and “-” buttons are
dedicated to the timer and no motor action will
occur.
Once the timer is initiated, it can be cancelled by
pressing the timer button again.
3. Display
Shows the hood settings.
The display will be lit at low intensity when the hood
is not operating.
Pressing any key the display will light up at high
intensity.
The display will be lit at high intensity when the hood
is operating.
If no key is pressed within a minute the display will
return to being lit at low intensity.
4. “-” Button. Speed Decrease / OFF
This button is used to decrease the fan speed, or
turn OFF the fan.
The fan will turn OFF if the “-” button is pressed and
the hood was in the first speed.
If the fan is at second speed and the “-” button is
pressed, the fan will be set to first speed.
If the fan is at third speed and the “-” key is pressed,
the fan will be set to second speed.
If the fan is at fourth speed and the “-” button is
pressed, the fan will be set to third speed.
If the fan is OFF and the “-” button is pressed, the
control backlight will light up.
5. “+” Button. Speed Increase / ON
This button is used to increase the fan speed, or
turn ON the fan.
The fan will turn ON if the “+” button is pressed and
the hood was OFF.
If the fan is at first speed and the “+” button is
pressed, the fan will be set to second speed.
If the fan is at second speed and the “+” button is
pressed, the fan will be set to third speed.
If the fan is at third speed and the “+” button is
pressed, the fan will be set to fourth speed.
If the fan is at fourth speed and the “+” button is
pressed, a beep will sound.
Clock programming
The clock can be reprogrammed at any time except
during an active timed function.
The clock can be displayed in a twelve hour format and
valid clock times are from 1:00 to 12:59.
The clock can be reprogrammed pressing the “Timer
button for 3 seconds, and after, the clock can be adjusted
with the “+” and “-” buttons.
The user can have minute increments / decrements of 1
minute, but if the user keep pressing the “+” / ”-” buttons
for more than 1 second, the increments / decrements will
be of 5 minutes.
During this option the control will round to the nearest 5
minutes.
The user can finish on reprogramming the clock pressing
the “Timer” button.
After 1 minute of no button pressed the control will accept
the programmed clock time and will add one minute to
the set clock.
Grease filter saturation alarm (Optional)
After thirty fan functional hours, the display will show
Grease Filter” if the fan is active.
When this icon is shown in the display, the grease filters
installed are required to be washed.
To reset the grease filter saturation alarm the user must
press the “+” button for 5 seconds, after this action the
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elica tender 90 ix at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elica tender 90 ix in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info