471224
8
Zoom out
Zoom in
Previous page
1/10
Next page
the extensions with 2 screws and fix the deflector to the
flues support bracket with 4 screws.
5. Hook the hood onto the lower support bracket.
6. Insert the lower part of the hood to the suction unit and fix
with 6 screws.
Attention! The hood is not yet definitively fixed to the
wall, every successive operation must therefore be
carried out with caution to avoid the hood unhooking from
the support bracket and causing damage to people or
things.
7. Connect the electricity between the two parts.
8. To assemble the steam screen and the flue-centring
bracket, use the screws and bushes supplied.
9. Fix the flue-centring steam screen - bracket unit above
the hood.
10. Adjust the distance of the hood from the wall and the
horizontal set of the hood with the 2 adjustment screws
on the hooks of the hood.
11. a. Definitely fix the steam screen-flue centring bracket
with 2 screws.
b. Additional small adjustments of the position of the
steam screen can be made loosening the 6screws from
inside the hood. Once the adjustment has been
completed, tighten the 6 screws up again.
12. Fix the motor unit to the support structure definitively:
make a Ø2.5 mm pilot hole on the support structure with
a drill, passing through the lower hole inside the motor
housing, after which fix definitively with 1 screw and
washer.
13. Carry out the connection of a tube (tube and strips for
fixing not supplied, to be purchased) for the discharge of
fumes to the connection ring over the suction motor unit.
The other end of the tube must be connected to a device
for the expulsion of fumes outside in the case of using
the hood in the suction version or to deflector F in the
case of using the hood in the filtering version.
14. Connect the electricity.
15. Apply the flues to cover the discharge tube, making the
plate extrude from the slot of the lower section of the flue.
Note: check that the tongues of the lower section of the
flue enter under the tongues of the centring bracket,
blocking it.
16. Fix with 2 screws.
17. Extract the upper part of the flue and fix it to the flues
support bracket „G“ with 2 screws.
18. Connect the plate to the control panel and fix it to the
rectangular slot (flush fixing).
Mount the frame of the carbon filter and the fats filter/s again
and check the perfect functioning of the hood.
Description of the hood
Fig. 1
1. Control panel
2. Grease filter
3. Grease filter release handle
4. Halogen lamp
5. Vapour screen
6. Telescopic chimney
7. Air outlet (used for filter version only)
Operation
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
A. on/off light switch.
B. on/off aspiration switch and minimum
power selection
B+C.medium power selection aspiration
switch
B+D.maximum power selection aspiration
switch
Maintenance
Before performing any maintenance operation, isolate the
hood from the electrical supply by switching off at the
connector and removing the connector fuse.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products.
DO NOT USE ALCOHOL!
Grease filter
This must be cleaned once a month (or when the filter
saturation indication system – if envisaged on the model in
possession – indicates this necessity) using non aggressive
detergents, either by hand or in the dishwasher, which must
be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Fig. 2
Charcoal filter (filter version only)
It absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two months (or
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elica Personal-corner at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elica Personal-corner in the language / languages: English as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info