471220

Elica Menhir Manual

7
Zoom out
Zoom in
Previous page
1/8
Next page
9
Consult the designs in the front pages referenced in the text by
alphabet letters. Closely follow the instructions set out in this
manual. All responsibility, for any eventual inconveniences, damages
or fires caused by not complying with the instructions in this manual,
is declined.
The cooker hood must be placed at a minimum distance of 50 cm
from the cooking plane for electric cookers and 75cm for gas or
mixed cookers.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only.
The hood is equipped with a top air outlet B for discharge of fumes
to the outside (Ducting version – exhaust pipe and pipe fixing
clamps not provided).
Should it not be possible to discharge cooking fumes and vapour to
the outside, the hood can be used in the filter version, fitting an
activated carbon filter and the deflector F
on the support (bracket) G, fumes and vapours are recycled through
the top grille H by means of an exhaust pipe connected to the top air
outlet B and the connection ring mounted on the deflector F (exhaust
pipe and pipe fixing clamps not provided).
The models with no suction motor only operate in ducting mode, and
must be connected to an external suction device (not supplied).
Expansion wall plugs are provided to secure the hood to most types
of walls/ceilings. However, a qualified technician must verify suitability
of the materials in accordance with the type of wall/ceiling. The wall/
ceiling must be strong enough to take the weight of the hood.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only.
Installation - Fig. 5-6-7-8
Preliminary information for installing the hood
During electrical connection ensure the power supply is disconnected
at the domestic main switch.
1. Adjust extension of the hood support structure, as the final
height of the hood depends on this, and remember that with
installation completed the hood must be at least 50 cm above the
cook-top for electric cookers and 70 cm for gas or mixed
cookers.
2. Fix the two sections of the structure using 8 screws.
3. Place the ceiling hole diagram directly above the cook-top (the
center of the diagram must match the center of the cook-top and
the edges must be parallel to the sides of the cook-top – the side
of the diagram with the wording FRONT corresponds to the
control panel side). Prepare the electrical connection.
4. Drill as shown (6 holes for 6 wall plugs – 4 plugs for fixture),
screw the outer screws leaving a space of about 1 cm. between
the screw head and the ceiling.
5. Fit an exhaust pipe inside the truss and connect it to the motor
compartment connection ring (exhaust pipe and fixing brackets
are not supplied).
6. Hook the frame onto the 4 screws (see step 4).
CAUTION! The side of the truss with connection box corresponds
to the side of the control panel with hood assembled.
7. Tighten the 4 screws.
8. Insert and tighten another 2 screws in the remaining free holes
for secure fixing.
9. Carry out the electrical connection to the mains power supply,
only turn on the power supply upon completion of assembly.
10. For extractor versions (10A), connect the other end of the
exhaust pipe to the flue.
For filter versions (10F), fit deflector F to the truss and secure it
to the bracket supplied using 4 screws, then connect the
exhaust pipe to the connection ring located on the deflector.
11. Remove the fixing tabs placed on the lower part of the chimney
flue, set aside the tabs and screws.
12. Apply the tabs to the inside of the upper section of the chimney
flue using one screw for each tab.
13. Fix the upper sections of the telescopic chimney flue (13a) to the
pylon (13b).
The upper sections are recognizable by the air exit perforations
for use in the filter version.
14. Block the sections with 2 screws (14a) to be inserted on the tabs
already mounted on one section of the chimney flue (14b – see
also the mounting sequence 11 -12).
15. Remove the grease filter and slide in the lower section of the
cooker hood (during this operation slightly widen the two sections
to ease the insertion).
The front side of the cooker hood is recognizable by the slit
opening provided for the control panel.
Attention! During this operation ensure to extract the control
panel plate and the electrical connection cables for the lamps
through the slit opening.
16. Fix the lower section of the cooker hood to the pylon from the
bottom using 6 screws (16a), and on the sides using 4 screws
(16b).
17. Introduce the cables CONNECTED to the lamps and connect the
control panel to the plate.
ATTENTION!
THE PLATE CABLE CONNECTOR IS PROVIDED WITH A SIDE
PIN THAT MUST COINCIDE WITH THE PERFORATION FOUND
ON THE SIDE OF THE CONNECTOR LOCATED ON THE BACK
OF THE CONTROL PANEL.
18. The double sided adhesive tape supplied should be cut into 8
segments, then remove the protection covering from both sides
and apply the segments close to the screws that fix the chimney
flues to the structure (see illustration for correct positioning).
19. Apply the 4 masks (supplied) to cover the fixing points of the
lower sections of the chimney flue (ATTENTION THE MASKS
FOR THE LOWER CHIMNEY FLUE ARE RECOGNIZABLE BY
THEIR NARROWER WIDTH).
The wider masks are to be used for the upper chimney flue, and
should be cut to size.
20. Hook the control panel to the opening slit so that the ON/OFF
light switch is facing downwards.
Remount the grease filter, turn on the power supply via the central
electrical panel and check that the cooker hood functions correctly.
Only for products supplied in stainless steel and aluminum:
Remove the protective covering taking care not to damage the metal
and finish (glazing).
Electrical connection
The electrical tension must correspond to the tension noted on the
label placed inside the cooker hood. Connect the electrical plug,
where provided, to the an easily accessible outlet in conformity with
local standards in force.
Where an electrical plug is not provided (for direct connection to
electrical network) place a standards approved bipolar switch with
an aperture distance of not less than 3mm (accessible) from the
contacts.
INSTRUCTION ON MOUNTING AND USE GB
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elica Menhir at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elica Menhir in the language / languages: English as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info