Manual Elica Elibloc 9 (page 9 of 28) (English, Italian, Polish, Polish)

649899

Zoom out

Zoom in

1/28

Operation

The hood is fitted with a control panel with aspiration speed

selection control and a light switch to control cooking area

lights.

The switch is located on the side of the suction grill H.

Use the high suction speed in cases of concentrated kitchen

vapours. It is recommended that the cooker hood suction is

switched on for 5 minutes prior to cooking and to leave in

operation during cooking and for another 15 minutes

approximately after terminating cooking.

Maintenance

ATTENTION! Before performing any maintenance operation,

isolate the hood from the electrical supply by switching off at

the connector and removing the connector fuse.

Or if the appliance has been connected through a plug and

socket, then the plug must be removed from the socket.

Cleaning

The cooker hood should be cleaned regularly (at least with the

same frequency with which you carry out maintenance of the

fat filters) internally and externally. Clean using the cloth

dampened with neutral liquid detergent. Do not use abrasive

products. DO NOT USE ALCOHOL!

WARNING: Failure to carry out the basic cleaning

recommendations of the cooker hood and replacement of the

filters may cause fire risks.

Therefore, we recommend observing these instructions.

The manufacturer declines all responsibility for any damage to

the motor or any fire damage linked to inappropriate

maintenance or failure to observe the above safety

recommendations.

Grease filter

Traps cooking grease particles.

If situated inside the support grill, it may be one of the

following types:

Paper filter must be replaced once a month or if colouring

appears on upper side, in such cases the colouring is evident

through the grill openings.

Metallic filter must be cleaned once a month, with non

abrasive detergents, by hand or in dishwasher on low

temperature and short cycle.

When washed in a dishwasher, the grease filter may discolour

slightly, but this does not affect its filtering capacity.

To access the grease filter J open the suction grill H via the

release hooks L and free from the supports K.

Some models are provided with a metallic filter M without

support grill, these should be washed as described above

and removed from their housing by pressing the N handles

towards the bottom.

Charcoal filter (filter version only)

It absorbs unpleasant odours caused by cooking.

The saturation of the charcoal filter occurs after more or less

prolonged use, depending on the type of cooking and the

regularity of cleaning of the grease filter.

In any case it is necessary to replace the cartridge at least

every four mounths.

The charcoal filter may NOT be washed or regenerated.

May be one of the following:

Rectangular: position the filter P in order to cover the motor

protection grill and turn the handle clockwise until locked-in,

for dismounting follow instructions in reverse.

Bayonet Circular-Insert position the filter in the centre (in

certain cases use the Z hooks for centring the filter) in order to

cover the motor protection grill ensuring that the X reference

on the carbon filter corresponds to the Y reference on the

conveyor, then turn clockwise; for dismounting follow

instructions in reverse.

Replacing lamps

Disconnect the appliance from the electricity.

Warning! Prior to touching the light bulbs ensure they are

cooled down.

Replace the old light bulb with the one of the same type as

specified in the feature label or near the light lamp on the

hood.

Remove the anti-grease filter support grill or the anti-grease

filter to access the lamp area. Remove the damaged lightbulb

and replace with an incandescent oval bulb maximum 40W

E14.

In the case where model is provided with a halogen lightbulb,

replace with halogen bulb of 20W (GU5.3 - Ø50mm).

If the lights do not work, make sure that the lamps are fitted

properly into their housings before you call for technical

assistance.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elica Elibloc 9 in the language / languages: English, Italian, Polish, Polish as an attachment in your email.

The manual is 1,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elica Elibloc 9 Manual

Product: