Manual Elica CLOUD SEVEN (page 15 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

784512

Zoom out

Zoom in

1/52

Operation

This product is designed to work with an Elica remote control,

either supplied with the product or purchased separately as an

optional.

To control the hood via remote control, the affiliation

procedure must be carried out.

CAUTION!

To begin, the hood must be disconnected and then

reconnected to the power supply and the affiliation procedure

must be carried out within the first minute of connection to the

power.

Read the instructions supplied with the remote control, which

provide detailed instructions on affiliation and correct use.

Note: the Speed 4 (and the Speed 5, where applicable) if

selected, will activate for a limited period of time after which

Speed 2 is automatically enabled.

Remote control connection (if applicable)

Once the remote control has been connected, this will be

displayed on the hood:

both LEDs flash.

Note: Using the remote control, delayed shut-down can be

programmed based on the aspiration speed (power) enabled

at that moment:

Speed 1 (low aspiration): 20 minutes

Speed 2 (medium aspiration): 15 minutes

Speed 3 (high aspiration): 10 minutes

Filter Saturation indicator lights

At regular intervals, the LEDs on the hood indicate the need to

carry out filter maintenance.

Note: The filter saturation signal is visible for a few seconds

when the hood is switched on; within this time, the

saturation indicator lights must be reset.

Flashing Green LED: carry out maintenance on the

grease filter.

Red flashing LED: carry out maintenance on the charcoal

filter (only for hoods operating in "Filtration Version").

Note: Run the "RESET FILTRES" command via the

remote control.

Activating/deactivating the filter saturation indicator

light

Note: Run the procedure with the hood switched off. The

charcoal filter saturation indicator light is usually

deactivated.

If no control is given within maximum 10 sec, the hood

automatically exits this function, at any time, and returns

to the previous state.

Press and hold the B+C keys (Simultaneously) to enter

the setup menu:

Briefly press button C to select the filter to be set up:

Grease filter:Green

Charcoal filter: Red

Briefly press button B to activate (the 2nd LED flashing)

or deactivate (2nd LED off).

Note: the LEDs light up for a limited number of seconds

after which they turn off to indicate that the indicator light

has been activated (or deactivated).

Maintenance

Cleaning

Clean using ONLY a cloth dampened with neutral liquid

detergent. DO NOT CLEAN WITH TOOLS OR

INSTRUMENTS. Do not use abrasive products. DO NOT USE

ALCOHOL!

Panel

Fig. 6

The panel for perimeter suction should always be left closed

and should only be opened in case of maintenance

interventions (eg cleaning or replacing filters).

Grease filter

Fig.7

Traps cooking grease particles.

This must be cleaned once a month (or when the filter

saturation indication system – if envisaged on the model in

possession – indicates this necessity) using non aggressive

detergents, either by hand or in the dishwasher, which must

be set to a low temperature and a short cycle.

When washed in a dishwasher, the grease filter may discolor

slightly, but this does not affect its filtering capacity.

To remove the grease filter, pull the spring release handle.

Replacing lamps

The hood is equipped with a lighting system based on LED

technology.

The LEDs guarantee an optimum lighting, a duration up to 10

times as long as the traditional lamps and allow to save 90%

electrical energy.

For replacement, contact the technical service.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elica CLOUD SEVEN in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1.09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elica CLOUD SEVEN Manual

Product: