471175

Elica Bridge Manual

15
Zoom out
Zoom in
Previous page
1/16
Next page
this does not affect its filtering capacity.
To remove the grease filter B, pull the spring release handle.
Charcoal filter (filter version only)
Fig. 3
It absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two months (or
when the filter saturation indication system – if envisaged on
the model in possession – indicates this necessity) using hot
water and a suitable detergent, or in a dishwasher at 65°C (if
the dishwasher is used, select the full cycle function and leave
dishes out).
Eliminate excess water without damaging the filter, then
remove the mattress located inside the plastic frame and put it
in the oven for 10 minutes at 100° C to dry completely.
Replace the mattress every 3 years and when the cloth is
damaged. Remove the filter holder frame by turning the knobs
(g) 90° that affix the chimney to the cooker hood.
Insert the pad (i) of activated carbon into the frame (h) and fit
the whole back into its housing (j).
It is possible to use a traditional carbon filter, neither
washable nor regenerable, to be replaced every 3 - 4 months.
The filter holder frame of the carbon filter is welded together;
the eventual frame supplied with the hood is not, therefore, to
be used.
Insert it into its housing and fix it turning the 2 plastic knobs.
Replacing lamps
Disconnect the hood from the electricity.
Warning! Prior to touching the light bulbs ensure they are
cooled down.
For models shown in Fig. 1E + Fig. 4E:
1. Press on the lamp cover and release to open.
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure
you do not touch them with your hands.
3. Close the lamp cover (it will snap shut).
For models shown in Fig. 1N/O + Fig. 4N/O:
1. Unscrew the lamp cover.
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure
you do not touch them with your hands.
3. Refit the lamp cover.
For models shown in Fig.1+Fig.4
(A/B/C/D/F/H/I/K/P/Q/S/T/U/V):
1. Extract the lamp cover by levering it off with a small
screwdriver or similar tool.
2. Replace the damaged light bulb.
Only use halogen bulbs of 20W max (G4), making sure
you do not touch them with your hands.
3. Close the lamp cover (it will snap shut).
For models shown in Fig. 1J + Fig. 4J:
1. Use a small screwdriver as a lever on the borders of the
lamp in order to remove the lightbulb.
2. Unthread the connector „a“.
3. Slide out the lightbulb to be replaced and replace with a
new 12V 20W 30° Ø35 12V GU4 PHILIPS STANDARD
LINE code 425409.
4. Carry out the replacement and mount the new lightbulb by
following instructions in the reverse.
For models shown in Fig. 1G + Fig. 5G:
Dismount the chimneys: remove the two screws (20 a)
that attaches the upper chimney to the support „G“ (Fig.
16).
Remove the box „q“: remove the screw „r“ that secures
the cooker hood.
Remove the lamp housing „s“: remove the screws „t“
that position the housing in the lamp housing area.
Extract the damaged lamp.
Use only PHILIPS type 14515 (GX 5.3) 12V - 75W
halogen bulbs..
Reposition and secure the lamp housing „s“ and the box
„q“ and remount the chimneys.
For models shown in Fig. 1K + Fig. 4K:
Certain versions of this cooker hood provide for an
incandescent lamp at 40W maximum (E14), remove the
lamp cover to access the lamp housing and carry out any
replacements.
Only for the illustrated model in Fig. 1L + Fig. 6L:
1. Open the front panel “v” upwards, which holds the lamp in
place, ensuring to hold the lamp “z” with one hand.
2. Replace the damaged lamp with one of identical technical
characteristics.
Attention! To guarantee the equivalent quality of lighting,
it is recommended to use the same type of lamp bulb:
Philips neon Lamp bulb 13W Code Ref. 8711500644305.
Ensure that the transparent part of the lamp bulb is facing
inwards so as to guarantee correct light distribution.
3. Replacing the starter:
Use a starter with identical technical characteristics.
Recommended starter: Use a Philips S10 starter.
4. Remount the lamp housing and the front panel in the
inverse in relation to the dismounting.
Only for the models illustrated in Fig. 1M + Fig. 7M:
1. Remove the grease filters.
2. Remove the ceiling light unscrewing the 3 screws that fix it
to the hood (hold the ceiling light to prevent it falling).
3. Change the damaged bulb with one with identical
technical characteristics.
Changing the starter
Use a starter with identical technical characteristics.
Starter advised: use a Phillips S10 starter.
4. Remount the ceiling light and the grease filters in the
reverse manner to the montage.
If the lights do not work, make sure that the lamps are fitted
properly into their housings before you call for technical
assistance.
Caution
Never use the hood without the grill mounted!
This appliance is designed to be operated by adults. Children
should not be allowed to tamper with the controls or play with
the appliance .
The premises must have sufficient ventilation when the
kitchen hood is used at the same time as other apparatuses
that use gas and other fuels.
… 15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elica Bridge at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elica Bridge in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info