Manual Elica Andante (page 9 of 12) (English)

471186

Zoom out

Zoom in

1/12

Mounting

Before starting to mount the appliance, make sure that no

component is damaged, otherwise contact the dealer and stop

mounting. In addition, read all the instructions below carefully.

• Use an air outlet pipe no longer than 5 metres.

• Limit the number of curves in the duct since each curve

reduces the suction effectiveness equivalent to 1 linear

metre. (E.g.: if two 90° curves are used, the duct should

be no longer than 3 metres).

• Avoid drastic changes of direction.

• Use a duct with 150mm diameter constant for the whole

length.

• Use a duct made of standard complying material.

• Remove the safety shim highlighted in the picture (Fig. 1-

2) at the end of the installation.

• In case of failure to observe the instructions above, the

supplier can not be held responsible for capacity or noise

problems and no warranty will be granted.

• Before making the hole, make sure that the inside of the

cabinet, near the hood housing area, does not have the

structure of the cabinet or other particulars which may

cause problems for the proper installation. Make sure

that the overall dimensions of the hood and the hob ae

compatible with the cabinet and therefore the installation

is feasible.

• Make a 848x100mm rectangular hole on the back of the

hob.

• In case of version with motor already mounted, remove

the screws and the suction unit to insert the hood into the

hole made.

• Install the hood in the hole made, inserting it from above,

as shown (Fig. 3). In case of version with motor on

board, it is necessary to remove the suction unit before

inserting the product into the cabinet.

• Fix the hood inside the cainet using the special brackets

supplied (Fig. 4). Start mounting the brackets in the lower

part of the hood (Fig. 5a) making sure that there is a

distance of 2 mm between the lower part of the bracket

and the cabinet bottom (Fig. 5b). This distance allows

the traction of the product downwards on fixing, (Fig. 5c),

so that the stainless steel frame adheres perfectly on the

worktop.

• Before inserting the screws into the cabinet, make sure

that the product is perfectly perpendicular to the worktop.

• After completing the installation and connecting the

product to the power supply, lift the hood and remove the

door lock (Fig. 6).

• In case of version with motor on board start mounting the

motor unit directing the air outlet to the chosen position

downwards or upwards (Fig. 7b). The motor can be

installed on both the front side and the back one of the

hood. Once the installationof the motor has been

comleted, start mounting the duct for the air outlet.

• In case of version with external motor put the suction unit

(external motor) in a suitable area and arrange the air

outlet duct. Start mounting the air outlet duct between the

external motor and the hood. Select the air outlet among

the five possibilities (Fig. 7a) and install the union

supplied.

• Put the metal box containing the electronic components

in an easily accessible area for any assistance

operations (Fig. 8), connecting the electric connectors of

the same to the hood: pushbutton panel connector (Fig.

9a), 9-pole connector (Fig. 9b), neon connector (Fig. 9c)

• In applications with external motor, connect the cable of

the motor unit to the special connector on the electronic

component box (Fig. 10a) in case an external control unit

SEM7 is used connect the 2-pole connector as well (Fig.

10b)

• Connect the product to the power supply

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elica Andante in the language / languages: English as an attachment in your email.

The manual is 3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elica Andante Manual

Product: