707570
11
Zoom out
Zoom in
Previous page
1/32
Next page
11
INSTALLATION MANUAL
7 ATTENTION POINTS GAS FLUE
To guarantee the fire safety regarding you flue gas configuration
a casing is necessary. For this case non-combustible materials
should be used. Make sure to ventilate a sha and never to
insulate it, to make sure the hot air is able to get away.
Every transit or terminal should be made such, that the warmth-
insulation and non-combustability is guaranteed, according to
the building regulation.
7.1 Installation of flue material
Follow the following instrucions for the installation of flue
materials;
Drill a hole of 100/125 mm for the roof transit and an
additional 10mm around.
Keep a distance of at least 5 mm between the outside of the
pipes and the wall or ceiling (Figure 6.3).
Provide a (fire) safe transit construction in wall, floor or roof
sheeting
Build the system from the fireplace.
Assemble pipes in the correct direction! The inner pipe goes
into and the outer pipe goes over the fireplace connection.
Make sure the tubes are su iciently braced, so the weight of
the tubes are not supported on the hearth.
The pipes could come loose due to expansion and cooling
down. It is recommended that a chuck parker be used in
places that are inaccessible a er installation.
7.1.1 Adapting the length of the chimney
Not all parts can be adjusted! To fit the drainage system correctly,
you are to use an adjustable fitting. You can use an adjustable
pipe and roof fitting.
Figure 8.1 - Gas Block Measuring Points
8 INSTALLATION CHECK AND FIRST USAGE
8.1 Renovation/new construction
When firing up the device for the first time, make sure the device
burns for several hours on the highest level, to ensure the lacker
to harden. Make sure the device is ventilated enough so the
possible released fumes are being abducted. We advice to be as
little in the room as possible during this process.
Because a fireplace is a heat source, natural convection will
occur around it. Solid particles in the circulating air may burn
and settle down on cold surfaces, causing discoloration.
Discoloration is an annoying problem and it is di icult to solve.
These particles can come from construction moisture or
cigarette smoke, but also they might be volatile components in
paint, construction materials or carpeting. For newly constructed
chimneys or a er a big reconstruction, it is advised to wait a
minimum of six weeks before firing a fireplace.
8.2 Checking the gas lines
To be able to check on the gas lines, it is necessary to have the
right equipment. If necessary take out the glass of the device
and use the measuring point (see figure 8.1), to check the supply
pressure on the gas pipes.
A = Supply pressure
B = Burner pressure
Make sure the cables of the ignition are hanging loosely under
the device, to ensure a good ignition. Remove any tie wraps or
other cable binders.
Check the pilot for obstructions and check the air tightness of
the system. Technical specifications can be found in
APPENDIX
E
.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Element4 Cupido 70 CF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Element4 Cupido 70 CF in the language / languages: English as an attachment in your email.

The manual is 8,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Element4 Cupido 70 CF

Element4 Cupido 70 CF User Manual - English, German, Dutch - 56 pages

Element4 Cupido 70 CF Installation Guide - Dutch - 36 pages

Element4 Cupido 70 CF User Manual - French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info