Manual Elektra Beckum SK260 (page 16 of 36) (English, German, Dutch, Spanish)

658064

Zoom out

Zoom in

1/36

3.0 General Information For Welding Transformer/Rectifier Operators

Dust, dirt and metal chips will harm any welding machine. It is of particular importance that the air ventilation for cooling

is not obstructed.

A weld should join two work pieces as if they were made from a single piece. Prior to the welding the joints must be

cleaned and dirt, rust, grease and paint removed. Also slag from previous welds must be completely removed. Attach

earth clamp firmly to work piece, assuring good metal to metal contact. Check that all cables and connectors are in proper

operating condition to ensure proper current conduction.

Place electrode with the uncoated end into one of the electrode holder's notches. Each welding machine is supplied

complete with an accessory kit, which includes besides the welding cables a welding visor and a slag hammer. When

removing slag it is recommended to protect the eyes by suitable means (goggles) from injury by sharp and hot slag. The

welding visor's dark glass plate protects the eye against ultra-violet and infrared rays. The clear glass plate protects the

dark plate against spatters and damage. The dark protective glass is available in different shades for different types of

electrodes and to suit different eye sensivity. Normally for electrodes from 1.5 mm to 4 mm Ø protective glasses of shade

DIN 9 are used, for electrode over 4 mm Ø shade DIN 10.

Select the correct welding current as shown below:

Current (A) Electrode Ø Material Thickness

15 - 50 1.0 - 2.0 mm 1.0 - 2.0 mm

50 - 100 2.0 - 2.5 mm 2.0 - 4.0 mm

100 - 140 2.5 - 3.25 mm 4.0 - 8.0 mm

140 - 220 3.25 - 5.0 mm 8.0 - 12.0 mm

220 - 300 5.0 - 6.0 mm 12.0 - 20.0 mm

In principle do not use too thick an electrode. As a general rule calculate 40 amps welding current per 1 mm of electrode

diameter. Depending on electrode type, material thickness and weld position this calculated value may have to be

adjusted to plus or minus.

All machines work well with thin plate from 1.0 mm thickness.

3.1 Care Of Stick Electrodes And Their Correct Use

In order to achieve a good weld the electrode has to be dry, thus storing in a dry place is essential- Should electrodes

have become moist, dry in an oven at between 200° C to 300° C for 30 minutes.

Basic coated low-hydrogen type electrodes always require pre-drying at 200° C to 300° C for 3 hours as atomic

hydrogen causes weld flaws.

Box 22 IP.. Degree of protection, e.g. IP21 or IP23.

Box 23 Symbol for protection class II, if applicable.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elektra Beckum SK260 in the language / languages: English, German, Dutch, Spanish as an attachment in your email.

The manual is 1,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elektra Beckum SK260 Manual

Product: