Manual Elektra Beckum SK200 (page 12 of 36) (English, German, Dutch, Spanish)

658062

Zoom out

Zoom in

1/36

SK 200 SK 230 SK 260 SB 200 SB 230 SB 260

Mains voltage 220 - 240 V 220 - 240 V 220 - 240 V 220 - 240 V 220 - 240 V 220 - 240 V

380 - 415 V 380 - 415 V 380 - 415 V 380 - 415 V 380 - 415 V 380 - 415 V

Mains frequency 50 H 50 Hz 50Hz 50Hz 50Hz 50 Hz

Welding steps stepless stepless stepless stepless stepless stepless

Current Range 25-200 A 25-230 A 25-260 A 20-200 A 20-230 A 30-260 A

Stepless at 220/240 V 25-110 A 25-114 A 25-120 A 20-110 A 20-114 A 30-135 A

Stepless at 380/415 V 40-200 A 40-230 A 40-260 A 30-200 A 36-230 A 75-260 A

Max. OCV

at 220 - 240 V 36.5 - 39 V 37.0 - 40 V 36.0 - 40 V 36.5 - 39 V 37.0 - 40 V 39.0 - 40 V

Max. OCV at 380 - 415 V 48.5 - 55 V 53.0 - 59 V 55 - 60 V 48.5 - 55 V 53.0 - 59 V 55.0 - 60 V

Max. input cap. at 220 - 240 V 4.3 kVA 4.5 kVA 4.4 kVA 4.3 kVA 4.5 kVA 4.5 kVA

Max. input cap. at 380 - 415 V 11.8 kVA 13.7 kVA 16.4 kVA 11.8 kVA 13.7 kVA 16.4 kVA

Working voltage 21.0-28.0 V 21.0-28.8 V 21.0-30.2 V 21.0-28.0 V 21.0-28.8 V 21.0-30.2 V

Cos - 220 - 240 V 0.77 (110 A) 0.77 (114 A) 0.80 (120 A) 0.77 (110 A) 0.77 (114 A) 0.8 (130 A)

Cos - 380 - 415 V 0.66 (200 A) 0.63 (220 A) 0.62 (260 A) 0.67 (200 A) 0.63 (220 A) 0.62 (260 A)

Duty cycle at max.

output 220 - 240 V* (25 / 40°) 25 %/ 17 % 25 %/ 17% 25 %/ 17% 20 %/ 15 % 55 %/ 40 % 50 %/ 35 %

100% duty cycle 220 - 240 V*

(25 / 40°) 55 A/ 35 A 60 A/ 40 A 55 A/ 35 A 50 A/ 35 A 85 A/ 60 A 90 A/ 65 A

Duty cycle at max.

output 380 - 415 V* (25 / 40°) 5 %/ 3 % 5 %/ 3 % 5 %/ 3 % 5 %/ 3 % 20 %/ 15 % 10 %/ 1,5 %

100% duty cycle 380 - 415 V*

(25 / 40°) - - - - - 90 A

Mains fuse 220 - 240 V 16 A time-lag 16 A time-lag 16 A time-lag 16 A time-lag 16 A time-lag 16 A time-lag

Mains fuse 380 - 415 V 25 A time-lag 25 A time-lag 35 A time-lag 20 A time-lag 25 A time-lag 35 A time-lag

Cooling self self self self fan fan

Insulation class F F FFFF

Protection class IP 21 IP 21 IP 21 IP 21 IP 21 IP 23

Dimensions (lxwxh) in mm 440x230x430 440x230x430 440x230x430 550x330x380 550x330x380 550x330x380

Weight 27 kg 31 kg 35 kg 40 kg 44 kg 44 kg

Accessory kit no. 7 8 8 130 8 8

Max. electrode diameter 5 mm 5 mm 5 mm 5 mm 5 mm 5 mm

2.1 Putting A combination 1-Ph/2-Ph Machine Into Operation

All "Combi" machines are supplied with a plug (CEE 5 pin 16/32 A) installed on the power cable. Connect to a 220 - 240 V

single-phase outlet with the adaptor supplied or to two phases of a 380/415 V 3-phase mains.

1.0 Specifications

- This welding machine should be connected to the power source via an Earth Fault Circuit Interrupter with 30 mA

capacity.

- Have worn or damaged power cables replaced immediately by a qualified electrician.

Do not operate the welding machine with a damaged power cable, danger of personal injury through electric shock.

- Children under the age of 16 should not operate this welding machine.

Connect to an earthed, single-phase 220 - 240 V outlet on a circuit protected by a 16 A time-lag fuse. Double insulated

machines (with PVC housing) do not require an earthed outlet. Operating other electrical machines or appliances on

the same circuit while welding is not recommended.

If your machine has detachable welding and earth cables, connect cables to the sockets, lock by turning plug clockwise.

With transformers the polarity does not matter, so both cables can be connected to either the + or - sockets. The same

applies for machines with permanently attached earth and welding cables.

Attach earth clamp to the work piece, close to the area to be welded and on to bare metal for good conduction. Place

a stick electrode into the electrode holder.

Set current selector switch to desired current. On all machines with stepless setting turn crank or handwheel until

desired current is indicated (stepless).

If there is no power outlet near the work piece an extension cable is required. The cable lead cross section must be

at least 2.5 mm

. The extension cable should be fully uncoiled to prevent heat build-up by inductance. Inductance also

considerably reduces the welding current. Extending the welding cables is also possible, however the cross section

of the extension cable should be larger than that of the cable supplied with the machine. Every machine is overload

protected by a thermo switch, which switches the transformer off if it becomes too hot. Let cool down until machine

switches on automatically. Some machines are equipped with a fan to increase the duty cycle through forced cooling.

The fan operates as long as the machine is switched on.

2.0 Putting A Single-Phase Machine Into Operation

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elektra Beckum SK200 in the language / languages: English, German, Dutch, Spanish as an attachment in your email.

The manual is 1,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elektra Beckum SK200 Manual

Product: