753500
49
Zoom out
Zoom in
Previous page
1/60
Next page
49
ESPAÑOL
3.3 SWK (refrigeración de
agua separada)
El mando totalmente automático de la
SWK es efectuado por la Powerbox.
Nota:
Más instrucciones para conectar
y operar la SWK se encuentran en el
manual de uso especial adjunto al
equipo.
3.4 Unidad de mandos
3.5 Unidad de mandos para
ajustes básicos del
equipo
Antes de establecer la conexión a la red
de alimentación eléctrica y antes de ini-
ciar la puesta en marcha es necesario
conectar los equipos entre sí. Los equi-
pos están ajustados de forma estándar
para la soldadura en atmósfera protec-
tora:
1. Elevar la SWK (refrigeración de
agua) con un ayudante y colocarla
sobre la Powerbox de modo tal que
las patas del equipo queden posi-
cionadas entre los tubos sobre la
estera de acanalado fino.
2. Elevar la SDV (alimentación de
alambre) con el ayudante y colo-
carla sobre la refrigeración de agua.
3. Establecer las conexiones de man-
gueras para el agua de refrigeración
de acuerdo a las ilustraciones
(véase también el manual de uso de
la SWK).
4. Establecer las conexiones de cables
de acuerdo a las ilustraciones.
La Powerbox está montada sobre un
bastidor con ruedas. Una vez montadas
la SDV y la SWK puede usted trasladar
el equipo de soldadura cómodamente
hacia el lugar de operación.
¡Peligro!
Antes de iniciar el transporte
cierre la válvula de la botella.
¡Peligro!
Considere usted que el equipo
de soldadura es bastante pesado.
¡Por esta razón el equipo puede esca-
parse del control especialmente en
terrenos con pendiente!
Antes de transportar el equipo de
18 Enchufe para conectar la ali-
mentación de corriente de
soldadura
19 Conexión para retorno de
agua hacia SWK.
20 Conexión para alimentación
de agua desde SWK.
21 Enchufe hembra para conec-
tar el cable de mandos
22 Activación de parámetros
(botón)
para activar el parámetro que
se desea visualizar y/o modifi-
car.
Los LED’s [23-26] indican cuál
parámetro se encuentra acti-
vado.
23 LED alimentación de alambre
[m/min]
24 LED corriente de soldadura
[A]
25 LED tensión de soldadura [V]
A
V
27
26
25
24
23
28
22
26 LED longitud del arco
voltaico [%]
27 Indicador de 7 segmentos
(de 3 dígitos)
En el display se visualiza:
valor del parámetro acti-
vado o bien
aviso de falla.
28 Modificación de parámetros
para ajustar el parámetro acti-
vado.
29 Tecla de introducción del
alambre
(Manual Wire Feed Drive)
30 Interruptor selector de
modos de operación
(Mode Selection)
31 Interruptor selector de
tiempo de separación de
alambre
(Wire burnback control)
32 Interruptor selector de tipo
de gas
(Gas-Type)
33 Interruptor selector de diá-
metro de alambre
(Wire Diameter)
34 Interruptor selector de tipo
de alambre
(Wire Type)
4. Montaje
34 33 32
29 30 31
5. Transporte
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elektra Beckum Mig Mag 502EP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elektra Beckum Mig Mag 502EP in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info