753500
17
Zoom out
Zoom in
Previous page
1/60
Next page
17
ENGLISH
Caution!
Check all connections and
supply lines before switching ON.
Caution!
At the workplace, secure the
machine against rolling away.
8.1 Control unit
The operating parameters are set and
displayed at the control unit.
With the pushbutton for parameter
selection, the parameter to be displayed
or adjusted is selected.
The following parameters can be
selected and displayed:
Wire feed [m/min]
Welding current [A]
Welding voltage [V]
Arc length [%]
The selected parameter is indicated by
the LEDs and its value is displayed on
the 7-segment display.
Using the parameter adjustment the
desired value, except the welding volt-
age, is set.
Wire feed
Via the parameter wire feed the feed
speed of the wire feed drive is set. The
best value for welding voltage and weld-
ing current is computed by the machine,
dependent on the selected charateristics
curve.
wire feed value range:
1.5 ... 19 m/min.
The value range available for adjustment
is dependent on the selected electrode
wire and the operating mode.
For manual arc welding the display is
disabled.
Welding current
The best current strength is determined
by the machine. During MIG/MAG weld-
ing the welding current can not be
adjusted. The set value can be adjusted
prior to welding via the parameter adjust-
ment.
For manual arc welding it is possible to
adjust the set value of the welding cur-
rent before the welding starts and also
during the welding process (actual
value).
Welding voltage
The welding voltage is displayed only. It
can not be adjusted.
Arc length
In MIG/MAG and pulsed MIG/MAG oper-
ating mode, the value set affects welding
voltage.
The adjustment range is from 50%
through 150%. 100% is the best operat-
ing point.
Note:
When using interconnecting torch
lead extensions, the occuring voltage
drop can be compensated by the param-
eter. In this case adjust to values of
110% ... 120%.
8.2 Gas-shielded arc welding
Caution!
Check before starting any
work:
Correct electrode wire installed?
Correct shielding gas connected?
Welding gun correctly fitted
(liner, spiral liner, contact tip, gas
shroud, support tube)?
1. Attach earth cable at suitable loca-
tion of workpiece.
2. Open cylinder valve and set desired
gas flow rate.
Change gas shroud, if necessary.
3. Set main switch at Powerbox and
mains switch of SWK to ON.
4. Adjust the machine’s default setting.
Selet charateristics curve.
5. Change parameters, if required.
The welding machine is now opera-
ble.
8.3 Manual arc welding
1. Attach earth cable at suitable loca-
tion of workpiece.
2. Set main switch of Powerbox to ON.
3. Select welding process ELE-
KTRODE.
The welding machine is now opera-
ble.
8.4 Shutting down
1. Close gas cylinder valve.
2. Set main switch to "0".
3. Disconnect earth cable from the
workpiece.
4. Unplug power cable.
This welding machine contains no user-
serviceable parts.
Depending on dust accumulation, the
Powerbox and the SDV should be blown
out with condensate-free compressed
air.
Periodically check all components for
visible damage.
Contact a qualified electrician if any of
the cables are damaged.
For models 232/ 302/ 402/ 502 EP the
accessories mentioned below are rec-
ommended. These accessories have
been tested with the machine and
ensure operation without any problem.
AWelding guns for 232 EP
1) SB 24/3
2) SB 24/4
3) SB 24/5
BWelding guns for 302 EP
1) SB 36/3
2) SB 36/4
3) SB 36/5
CWelding gun for 402 EP and
232/302 EP with water cooling
1) SB 41/W3
2) SB 41/W4
3) SB 41/W5
DWelding guns for 502 EP
1) SB 51/W3
2) SB 51/W4
3) SB 51/W5
EEarth cable
1) 5 m, 25 mm2 for 232 EP
2) 5 m, 50 mm2 (copper jaws)
for 302/ 402 EP
3) 5 m, 70 mm2 (copper jaws)
for 502 EP
FInterconnecting torch lead exten-
sion
for 232/302 EP
1) 5 m, 50 mm2, gas-cooled
2) 10 m, 50 mm2, gas-cooled
GInterconnecting torch lead exten-
sion for 232/302/402 EP with water
cooling
1) 5 m, 50 mm2, water-cooled
2) 10 m, 50 mm2, water-cooled
HInterconnecting torch lead exten-
sion
for 402/502 EP
1) 5 m, 70 mm2, water-cooled
2) 10 m, 70 mm2, water-cooled
IPressure gauge with 2 gauges and
stop valve.
8. Operation
Shielding gas amount in l/min Aluminium Steel
Welding current in A
Gas shroud diameter
in mm
9. Maintenance
10. Available Accessories
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elektra Beckum Mig Mag 502EP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elektra Beckum Mig Mag 502EP in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info