753500
14
Zoom out
Zoom in
Previous page
1/60
Next page
14
ENGLISH
3.5 Control unit for default
machine settings
The individual components need to be
connected to each other before being
connected to the mains and before inital
operation. By default the components as
set for gas-shielded arc welding:
1. With the help of another person lift
the SWK (water cooling unit) and
place it on the Powerbox, to that its
feet stand between the pipes on the
rubber mat.
2. With the help of another person lift
the SDV (wire feed unit) and place it
onto the water cooling unit.
3. Connect the coolant hoses as illus-
trated below (see also the SWK
instructions).
4. Connect the cables as illustrated
below.
The Powerbox is mounted on a wheel
set. With fitted SDV and SWK the com-
plete welding machine is conveniently
moved to the workplace.
Danger!
Close the cylinder’s valve
before relocating.
Danger!
Note the hight weight of the
welding machine. It may get out of
control, especially on sloping
ground!
Walk along the intended way, before
you set off with the welding machine.
Ask another person for assistance, if
necessary!
5.1 Crane hoisting
The welding machine can be hoisted by
crane.
Danger!
Remove the gas cylinder
before hoisting.
Hoisting with the gas cylinder is for-
bidden!
1. Fit the hoisting straps as illustrated
below.
Caution!
At the workplace, secure the
machine against rolling away.
6.1 Manual arc welding
When setting the machine for manual
arc welding, you must:
1. Check all connections.
Disconnect earth cable (- pole) and
welding current supply cable
(+ pole).
2. Connect earth cable to the Power-
box - pole).
3. Connect welding cable to the weld-
ing current supply cable (+ pole).
6.2 Gas-shielded arc welding
1. Check all connections. Disconnect
earth cable (- pole).
The welding current supply cable
(Powerbox) must be connected to
the connector plug of the welding
current supply (SDV).
25 LED welding voltage [V]
26 LED arc length [%]
27 7-segment display (3 digits)
The display shows:
the value of the selected
parameter or
an error message.
28 Parameter adjustment
to adjust the selected parameter.
29 Wire thread-in button
(Manual Wire Feed Drive)
30 Operating mode selector switch
(Mode Selection)
31 Burnback time selector switch
(Wire burnback control)
32 Gas type selector switch
(Gas Type)
33 Wire diameter selector switchr
(Wire Diameter)
34 Wire type selector switch
(Wire Type)
4. Installation
34 33 32
29 30 31
5. Transport
6. Preparing for Operation
A
V
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elektra Beckum Mig Mag 502EP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elektra Beckum Mig Mag 502EP in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info