625958
13
Zoom out
Zoom in
Previous page
1/16
Next page
5. Release the gas control knob then check that the burner is alight by looking in the flame control tube. If
the burner has not lit, repeat the lighting procedure.
Note:- The refrigerator has a flame failure device which will automatically shut off the gas to the burner if
the flame is blown out- While the knob (4) is being pressed in, this device is temporarily inoperative.
Lighting the Burner (Models with Electronic Igniter)
For models fitted with the electronic ignition system follow Item
16 up to point 2 then proceed its follows:-
3. Switch on the electronic igniter switch by pushing in the right-hand end
against the symbol '1'. The light in the switch should start Fleshing,
Indicating that sparking is taking place
4. Turn the gas control knob (4) to the maximum position (No, 3) then
press in this knob end keep it held in
5. When the burner lights, the neon tight in the switch will stop flashing
and go out, When this happens, keep the knob (4) held in for a further 15 seconds for the thermocouple
over the burner to heat up, then release the button- If the light in the switch Starts flashing again it
indicates that the flame has gone out. In this case, repeat operation No5.
6. When the burner has lit, leave the igniter switch in the 'On' position, if the flame goes out, due to a gust
of wind for instance, the igniter will then immediately start sparking and re-light the burner.
Note: If the burner does not re-light within about a minute, the flame failure device will operate and shut off
the flow of gas to the burner-The neon light in the switch will still continue to flash, however, to alert you
that something is wrong or that the gas bottle is empty
Emergency Lighting Procedure for Gas Burner
Although the electronic igniter is primarily designed for connection to a 12V car battery, it will operate from
a 9V dry cell. If the recommended car battery connection is not available- the burner can be lit by using a
type PP3, PP7, PP9, or equivalent battery, as used for radios etc. If using this method, '+'and'-' polarity
must be observed otherwise the igniter will not operate.
17.Electric Operation (230V a.c.) Model RM123 only.
IMPORTANT: Before connecting any mains voltage electricity supply to a caravan, always make certain
that the supply has an effective earth connection and that polarity is correct in relation to the, mains
voltage wiring in the caravan. For safety, it is essential, particularly for overseas use, to check for earth
continuity and correct polarity of the connected supply. (There are different makes of proprietary polarity
and Earth Continuity monitors on the market for this purpose).
To start the refrigerator on mains voltage electricity,
see that the gas control knob (4, fig. 14a), the igniter switch (5, fig. 14a), and the 12V supply are off.
Connect the refrigerator to the electricity supply socket and switch on. Turn the electric thermostat dial (6,
fig. 15) so that setting 3 or 4 is against the indicator mark.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Electrolux RM 123E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Electrolux RM 123E in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info