310319

Electrolux ew 1200 f intuition Manual

27
Zoom out
Zoom in
Previous page
1/32
Next page
27
Water drainage
This appliance is designed to be permanently plumbed
into your home's water supply and drainage system.
The appliance drain hose should hook into a standpipe,
the hook in the drain hose is formed using the plastic
“U-Piece” supplied.
The standpipe should have an internal diameter of
approximately 38mm (see diagram) thus ensuring there
is an air break between the drain hose and standpipe.
When discharging into a standpipe ensure that the top of
the curve in the hose end is no more than 90cm (35.4'')
and no less than 60cm (23.6'') above floor level. The
upright standpipe should have a minimum length of
30cm (12'') from the bottom of the elbow to the top of
the pipe (see diagram).
Make sure that it is designed in such a way, that the end
of the drain hose cannot be covered with water.
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece
is available from your local Service Force Centre.
The joining piece must have an internal diameter of
18mm.
If you intend the drain hose to empty into a sink, make
sure that the sink is empty and the plug hole is not
blocked. Use the plastic “U-Piece” supplied.
P0022
P1039
3 pin
Max. 90 cm.(35.4")
Min.60 cm.
(23.6")
P1040
Min. 30 cm.(12")
38 mm.(1/ ") diameter
standpipe
1
2
Water inlet
The inlets on the back of the appliance are colour coded,
blue for cold and red for hot.
Connect the hoses to a tap with a 3/4'' thread.
If only a cold water supply is available, connect the two
hoses to a cold water outlet by means of a «Y»
connection piece.
Installation should comply with local water authority
and building regulations’ requirements.
The appliance must be given a separate cold water
supply and not be connected to a mixer tap, a single
outlet water heater or a booster pump. A minimum
water pressure of 0.48 bar is required for safe operation
of the appliance.
If you cannot make the cold water connection direct
from the rising mains, you may be able to operate the
appliance from your cold water storage system.
There should be a minimum distance of 5.02m
(16.5 ft) between the appliance’s inlet and the bottom of
the water storage tank.
There will be sufficient pressure for the hot water
supply, providing there is a minimun height of 2.74
metres (9 ft) between the bottom of the cold water
storage tank and the bottom of the hot water cylinder.
Set the hoses correctly by loosening the ring nuts. After
positioning the inlet hoses, be sure to tighten the ring
nuts again to prevent leaks.
P0021
P1088
132996240.qxd 6/20/01 8:27 PM Pagina 27 (Nero/Process Black pellicola)
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Electrolux ew 1200 f intuition at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Electrolux ew 1200 f intuition in the language / languages: English as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info