127328
91
Zoom out
Zoom in
Previous page
1/96
Next page
Once these checks have been carried out
switch on the appliance.
The programme will continue from the point
at which it was interrupted.
If the malfunction or fault code reappears
contact your local Service Force Centre.
For other fault codes not described in the
above chart, please contact your local Serv-
ice Force Centre.
Contact your local Service Force Centre,
quoting the model (Mod.), product number
(PNC) and serial number (S.N.).
This information can be found on the rating
plate located on the side of the dishwasher
door.
So that you always have these numbers at
hand, we recommend you to make a note of
them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The wash results are not satisfactory
The dishes are not
clean
The wrong programme has been selected.
The dishes are arranged in such a way as to stop water reaching all parts
of a surface. The baskets must not be overloaded.
The spray arms do not rotate freely due to incorrect arrangement of the
load.
The filters in the base of the washing compartment are dirty or incorrectly
positioned.
Too little or no detergent has been used.
Where there are limescales deposits on the dishes; the salt container is
empty or incorrect level of the water softener has been set.
The drain hose connection is not correct.
The salt container cap is not properly closed.
The dishes are wet
and dull
Rinse aid was not used.
The rinse aid dispenser is empty.
There are streaks,
milky spots or a blu-
ish coating on
glasses and dishes
Decrease rinse aid dosage.
Water drops have
dried onto glasses
and dishes
Increase rinse aid dosage.
The detergent may be the cause. Contact the detergent manufacturer con-
sumer care line.
If after all these checks, the problem persists,
contact your local Service Force Centre.
Technical data
Dimensions Width
Height
Depth
60 cm
85 cm
63,5 cm
Electrical connection - Voltage -
Overall power - Fuse
Information on the electrical connection is given on the rating plate
on the inner edge of the dishwasher door.
Water supply pressure Minimum
Maximum
0,05 MPa (0,5 bar)
0,8 MPa (8 bar)
Capacity 12 place settings
Hints for test institutes
Testing in accordance with EN 60704 must
be carried out with appliance fully loaded and
using the test programme (refer to 'Con-
sumption values').
electrolux 91
91


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Electrolux esf 66710 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Electrolux esf 66710 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 15,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info