577299
5
Zoom out
Zoom in
Previous page
1/52
Next page
Operating instructions
Controls
M
H
B C D E F
A
G
L
I
Operation mode DHW (M)
For switching on the DHW operation
(indication in display below DHW symbol)
Operation mode heating zone(s) (I)
For setting 4 different heating modes:
Auto (clock): Automatic operation by
time programm
Comfort (sun): 24/7 heating in
comfort mode
Reduction (moon): 24/7 heating in
reduced mode
Standby: heating off, frost protection
activated.
Display (L)
Info mode (G)
Display possibility of following info
without influence on boiler control:
temperatures, operation mode
Heating / DHW, error code.
Room temperature control (C)
for changing room comfort
temperature
for changing setting when
programming.
On/off switch (A)
Position 0:
Boiler and connected electrical
components are not powered.
Frost protection is not secured.
Position I:
The boiler and connected electrical
components are powered and standby
for operation.
Confirmation (OK) (D)
Return (ESC) (B)
These buttons are used for
programming in combination with the
rotary knob.
By pressing the ESC button it‘s possible
to go back one level, changed values
are not taken over by the controller.
By pressing the OK button it‘s possible
to arrive in the next level or confirm
changed values.
Manual mode (E)
This button is used for switching the
boiler into manual mode. In manual
mode all pumps will run and the mixing
valves are no longer controlled, the
burner setpoint is 60°C (indicated by
spanner symbol).
In the display, the spanner symbol is
shown. This manual mode should be
used as a temporary measure to assure
proper functioning of the boiler in case
of a disfunctional controller or wrong
settings, and should in no case be
applied for a longer period.
Deaeration mode (E)
By pressing the manual mode button
longer than 3 seconds, the automatic
hydraulic deaeration is activated e.g.
after first filling the system. During
deaeration the system is put in standby /
protection mode .
The pumps are switched on and off for
several times.
After deaeration, the boiler automatically
returns to normal operation.
Legend:
A On/off switch
B Return (ESC)
C Room temperature control
D Confirmation (OK)
E Manual mode
F Chimney sweeper mode
G Info mode
H Reset button
I Operation mode heating zone(s)
L Display
M Operation mode DHW
Chimney sweeper mode (F)
Used for combustion analysis. By
pressing the button once again, or
automatically after 15 minutes, the
chimney sweeper mode will be
deactivated (indicated by spanner
symbol).
In case a mixing circuit is part of the
heating system, the control continues
normally.
Reset Button (H)
By shortly pressing the reset button a
burner lockout can be cancelled.
Notes:
a After pressing reset once, wait for
ca. 20 seconds (LMU initialising,
error code 132 shows briefly; Gas
flow control input is checked).
b When pressing reset twice, the LMU
controller is locked manually (error
code 153).
Press reset again.
c Pressing reset without error code
triggers error code 153
5
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elco Thision S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elco Thision S in the language / languages: English as an attachment in your email.

The manual is 2,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Elco Thision S

Elco Thision S User Manual - German - 20 pages

Elco Thision S User Manual - Dutch - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info