646322
28
Zoom out
Zoom in
Previous page
1/46
Next page
M
A
H
B C D E F
I
L
G
0
I
A
Commissioning
30
Prepare boiler for rst startup
Legend:
A On/o switch
B Return (ESC)
C Room temperature control
D Con rma on (OK)
E Manual mode
F Chimney sweeper mode
G Info mode
H Reset bu on
I Opera on mode hea ng zone(s)
L Display
M Opera on mode DHW
It‘s recommended to put the boiler
on 50% load a er the rst startup, as
this is the best star ng point to do a
proper combus on analysis. This can
be done with the following proce-
dure:
Push bu on I >3 Secs, the boiler
goes into controller Stop mode.
Push the Info bu on (G), the ac-
tual boiler load (%) appears in the
display;
Choose „set up“ (con rm with OK
bu on), now the boiler load can
be changed by rota ng the wheel
(C) and con rming the 50% set-
ng with the OK bu on.
LPG (G31) Se ngs
In order to operate with G31 gas
type reaching the related parameters
(9524 min. rpm and 9529 max. rpm)
on the display. Values of rpm are
listed on page 9:
• Push OK bu on
• Push (G) for 3 seconds
• choose installer with wheel (C)
• Push OK bu on
• choose branderautomaat with
wheel (C)
• Push OK bu on
• choose parameternumber you
want to change with wheel (C)
OK (parameter is blinking)
change value with wheel (C)
OK (parameter is stored)
A er checking the combus on val-
ues (see next page), the controller
Stop mode can be exited by pushing
the control mode bu on (I) >3 Secs.
Ini al procedures
To guarantee safety and the correct
opera on of the appliance, the boiler
must be prepared for opera on by a
quali ed technician who possesses
the skills which are required by law.
Electricity supply
Check that the voltage and fre-
quency of the electricity supply
correspond to the data shown on
the boiler data plate;
Make sure that the earthing con-
nec on is e cient.
Filling the hydraulic circuit
Proceed in the following manner:
Open the system lling point and
vent the hydraulic system. Con -
nue lling the system un l pres-
sure gauge on the boiler registers
1.5 bar
Gas supply
Proceed as follows:
Make sure that the gas supply de-
livers the same type of gas as in-
dicated on the boiler data plate;
ATTENTION: The Boiler is set for
G20-G25 gas type. To operate with
G31 gas type use the procedures
described on “LPG se ngs”.
Open all doors and windows;
Make sure there are no sparks or
ames in the room;
Make sure that the gas connec-
ons are sound.
Prepara on for rst startup
Open the gas supply;
Enable the power supply to the
boiler;
Switch on the boiler with the on/
o switch (A);
Make sure the boiler is in standby
mode ( );
Check the pump opera on: make
sure the pump runs in the right di-
rec on;
Release all air from the pump mo-
tor.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elco THISION L EVO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elco THISION L EVO in the language / languages: English as an attachment in your email.

The manual is 8,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info