Manual Elco R3600 (page 32 of 192) (English, German, Dutch, French, Italian)

569725

Zoom out

Zoom in

1/192

Operating instructions

Main menu (operating mode)

Parameter menu (information/programming mode)

Changing parameter values

The boiler controller has two menus: the main menu (operating mode) when the lid is closed, and the parameter menu

(information/programming mode) when the lid is open. Both menus and possibilities are explained in the next paragraphs.

Main menu (operating mode) lid closed

With the lid closed and by using the rotational switch (1) clockwise or anticlockwise

the boilers’ operating mode (2) can be set. The available modes are:

K Standby mode (only frost protection)

F Automatic operation mode (heating and DHW)

F Summer mode (only DHW, no heating)

W1 Service mode minimum load

W2 Service mode full load (limited by P9)

Besides the operating mode, the display also shows the actual water flow tempera-

ture (3) and, in case of a lockout, a warning triangle (4) combined with a lockout

code (5). The explanation of the lockout codes can be found in chapter

“Lockouts”.

Parameter menu (information/programming mode) lid open

With the lid open and by using the rotational switch (1) clockwise or anticlockwise

it’s possible to read/change certain values/parameters from the boiler controller.

An arrow at the bottom of the display (2) indicates which parameter has been se-

lected. The available values/parameters are:

P1 Actual / setpoint water flow temperature [ºC]

P2 Actual / setpoint DHW temperature [ºC]

P3 Actual temperature/capacity setpoint for boiler [ºC]*

P4 --

P5 Actual outside temperature [ºC] (if sensor is connected)

P6 Actual fluegas temperature [ºC]

P7 --

P8 Actual low velocity header temperature [ºC] (if sensor is connected)

P9 Actual / Limit boiler output [%]

P10 Password for advanced settings

Press the reset/programming button

to select (the LED lights up)

Turn the rotational switch until the

desired DHW setpoint value has been

reached

Press the reset/programming button

to confirm (the LED goes out)

Close the lid.

Output indications

Power to main gas valve

Power to ignition transformer

Fan control signal

Z Power to primary boiler pump

F Power to DHW pump/diverter valve

Behind the lid you find an optical I/O

connection (6), a reset/programming

button (7) and an alarm/programming

LED (8). Besides the parameter values/

settings, the display also shows additio-

nal information with regard to input and

output indications to and from the boi-

ler:

Input indications

Flame ionisation detected

SW Water flow switch active

DW Air pressure switch active

RT Boiler enabled**

Bus Bus communication active

Changing parameter values

For changing any parameters, in the

example parameter P2 (DHW setpoint),

the following procedure should be car-

ried through:

Open the lid (the arrow at the bottom

of the display indicates parameter P1)

Turn the rotational switch clockwise

until the arrow indicates parameter P2

The new value is now activated. All

parameters can be changed by follo-

wing the same procedure as described

above.

**The boiler enable signal is equipped with a jumper in the standard delivery and therefore the boiler will normally be enabled. If a building

management system is connected to provide the enable signal to the boiler (jumper should be removed), check the building management

system if the boiler remains disabled.

* P3 shows the actual temperature setpoint of the boiler, either coming from P1/P2 or from an additional (weather compensated) controller or

building management system (2-10V). When the boiler capacity is controlled via a cascade manager or building management system (2-10V),

P3 shows the actual capacity setpoint of the boiler.

2 5 3 4 1

2 1

6 7 8

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Elco R3600 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 5,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Elco R3600 Manual

Product: