646319
20
Zoom out
Zoom in
Previous page
1/49
Next page
20 of 49
Condense Connection
Commissioning
Preparation for operation
General
To ensure the safe and correct operation
of the boiler, commissioning must be
carried out by a suitably qualified
specialist.
Monitoring
Ensure condensate connection is
connected using the condense drain
hose supplied or using plastic piping.
Ensure that the Condense outlet is
piped to a suitable drain. Please refer to
BS6798 for ultimate guidance
First commissioning
Fill hydraulic circuits
Proceed as follows:
Open the boiler bleed valve and the
valve above the stainless steel heat
exchanger.
Loosen the closure of the automatic
bleed valve on the circulation pump.
Slowly open the system filling point
and shut the bleed valve on the
stainless steel heat exchanger, and
the boiler, as soon as water is
evident. Shut the filler valve, once
the pressure shown on the water
pressure gauge reaches 1.0 bar.
Ensure that:
The the automatic bleed valve on
the circulation pump is opened.
The boiler pressure, on the
manometer is 1 bar. The gas valve
is completely shut off. The electrical
connection has been correctly
made.
Ensure in every case, that the
green/yellow earth wire is connected to
a suitable earth.
To bleed the appliance, proceed as
follows:
Switch on boiler (10). This sets the
pump of the heating appliance in
operation and there are three
consecutive attempts to ignite the
burner. After the third attempt the
electronics lock the appliance, as
the gas supply is cut; the display
shows the readout "133".
Allow the pump to work until all the
air has left the appliance. Vent the
boiler. Check the appliance
pressure and refill with water in the
case of a drop in pressure, until
pressure again reaches 1 bar.
Check the flue gas system.
Ensure that any necessary room
ventilation openings are open.
Ensure the boiler condensation
siphon is filled with water.
(See illustration below centre).
If the appliance is unused for a long
period, the siphon must be filled
before switching on again. It is
dangerous not to refill the siphon with
water, as this can cause the flue gas
to escape from the condense drain.
Open the gas tap and check the
tightness of all connections. Unlock
the boiler by pressing the Reset key
"6". The burner will ignite. Should this
not happen, repeat the above
procedure, until the burner ignites.
Gas supply
Proceed as follows:
Ensure that the type of gas used
corresponds to the type of gas
indicated on the nameplate of the
boiler.
Power supply
Ensure that the voltage and frequency
of the power supply conform to the
data on the name plate of the boiler.
Ensure that the live and neutral
connections have been made and to
the correct terminals. Check that the
earth is connected.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elco MHS - EURON 24 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elco MHS - EURON 24 in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info