561004
8
Zoom out
Zoom in
Previous page
1/22
Next page
Anschluss eines
Subwoofers
Connection of a subwoofer
低音音箱
接线图
- 8 -
Der richtige Anschluss des Subwoofers in
einer Surroundanlage ist von vielen Kriterien
abhängig. Es können auch mehrere
Anschlussvarianten “richtig” sein. Beachten
Sie in diesem Zusammenhang auch die
Bedienungsanleiitungen des AV-Verstärkers
und der mitverwendeten Lautsprecher
The correct connection of a subwoofer to a
surround set depends on many criteria.
Several hook-up options may be "correct". As
a result, careful consideration should be given
to the users manuals of the AV amplifier and
the loudspeakers used in the set-up.
正确连接立体声设备的低音音箱取决
于许多规范。也有很多种“正确”的
连接方式。因此连接时请注意AV放大
器和所用的音箱的说明。
1 Cinch-Verbindung, Surround, spezieller Subwoofer-Ausgang
1 RCA connection, surround,
specific subwoofer output
1RCV连接,环绕声,专
用低音音箱输出端口
An Surround-Verstärkern finden sich in der Regel spezielle Subwoofer- Ausgänge,
die sich für den Anschluss aktiver Subwoofer eignen. Dieses Mono-Signal wird mit
dem Line-Eingang (LINE LEVEL IN) des ELAC Subwoofers verbunden. Die
Subwoofer-Ausgänge an Surround-Verstärkern führen dem ELAC Sub nur
entsprechende Basssignale zu, daher sollte die Übergangsfrequenz am ELAC
Subwoofer zunächst auf Maximum eingestellt werden (180 Hz). Tiefere
Übergangsfrequenzen sind nur einzustellen, wenn der Klang durch zu starken
oberen Bass tendenziell zu dick und undurchsichtig sein sollte.
On many surround decoders you will
find a specific subwoofer output, which
is ideally suited to powered subwoofers.
This mono signal is connected to the
line input (LINE LEVEL IN) at the ELAC
subwoofer. Since the subwoofer outputs
on surround amplifiers only feed filtered
bass signals to the ELAC subwoofer,
the crossover frequency at the ELAC
sub should be set at the maximum value
(180 Hz). Lower crossover frequencies
should be chosen only, if the sound is
too thick and muddy due to excessive
upper bass.
如果连接环绕声放大器则使用有
源音箱接线的专用低音音箱输出
端口。此单道信号将利用线性输
入端(LINE LEVEL IN)与ELAC
音箱连接。
连接环绕声放大器的音箱输出端
只传导与ELAC Sub音箱相符合的
低频信号,因此ELAC音箱的分音
频率在开始时要调至最大(180
Hz)。只有当上低音过重导致音
调趋向过厚和不清晰时,才设置
较低的分音频率。
Falls Ihr Surround-Verstärker keinen ‘SUB OUT' besitzt, aber auch für den Fall,
dass das Klangbild im zuvor beschriebenen Anschlussverfahren durch das Bass-
Management des AV-Receivers nicht zufriedenstellend ist, können alternativ
auch nachfolgende Anschlussvarianten sinnvoll sein. Die für Sie optimale
Variante ist durch Probieren zu ermitteln.
If your surround amplifier does not
have a ‘SUB OUT', and the sound
image in the above described hook-up
variety appears due to the bass
management of the AV receiver, the
following hook-up options may be
preferable. Test several options to find
your optimum configuration.
如果您的环绕声放大器没有“
SUB OUT”接口,也就在这种
情况时按照前面描述的方法连接
通过AV接收器的低频控制系统
音质仍不能令人满意时,可以采
用下列的连接方式。
这些选择方案需要您通过尝试获
得最佳效果
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Elac SUB 111.2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Elac SUB 111.2 in the language / languages: English, German as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info