Manual EK63-EdilKamin Firek 3 (page 21 of 24) (English)

810958

Zoom out

Zoom in

1/24

USER INSTRUCTIONS

Ignition with the combustion chamber cold.

1. Check that the existing ash bed is not too high. If

the ash bed becomes too high there is a danger that

hot embers may fall out of the combustion chamber

when the combustion chamber door is opened to add

wood.

2. Move the lever for regulating the air valve to the

“fully open” position. There will be an intense ﬂ ow

of combustion air to the wood in the combustion

chamber allowing quick and eﬃ cient combustion.

3. Place the wood in the combustion chamber without

packing it excessively. Place an ignition unit among

the logs, and ignite. Never use ignition products such

as petrol, alcohol and the like.

4. At this point, close the door and monitor for a few

minutes. If the ﬁ re should go out, open the door

slowly, place another ignition unit among the logs and

ignite it again.

Adding wood when the combustion chamber is

hot

When is the right time to add wood? When the fuel

has almost ﬁ nished and is in hot embers. Using the

glove, open the hinged door slowly (to avoid the

creation of air vortices which could cause smoke to

leak out). Add the desired quantity of wood into the

combustion chamber, placing it on top of the existing

embers (within the quantity limits indicated in the

technical sheet).

Operation with low initial draught

In order to draw in the air for combustion and to

discharge the smoke, the combustion chamber

needs the draught created by the ﬂ ue.

If the draught is weak, initially light a “start up” ﬁ re

using smaller pieces of ignition material.

Once the correct level of draught has been restored,

you can add the fuel.

As with all appliances, a wood appliance heats up and

cools down during the various operating stages. This

causes normal levels of expansion. This expansion

may cause slight settling noises that cannot be used

as a cause for complaint

as a cause for complaint.

FUEL

The product is designed for burning wood pellets or

logs. Use dry wood logs (max. 20% humidity)

Using damp wood will make the product and ﬂ ue

dirty, risk the release of smoke and provide a lower

heat output.

Each type of wood has diﬀ erent properties that

inﬂ uence the output of the combustion process.

The data given in this manual refers to the wood used

during certiﬁ cation.

Generally speaking, wood has a caloriﬁ c value of

approximately 4.5 kWh/kg. When freshly cut it has a

caloriﬁ c value of approximately 2 kWh/kg.

Generally speaking, we recommend using beech,

elm or other class A1 woods in accordance with UNI

EN ISO 17225-5.

Avoid the prolonged use of woods rich in aromatic

oils (e.g. eucalyptus). This may deteriorate the cast

iron components.

Use the recommended quantities of wood.

Overloading may lead to overheating, causing the

following damage:

•possible buckling of the internal parts;

• possible irreversible alterations in the colour of

the paint on the metal parts, for which neither

Edilkamin nor the retailer can be held responsible.

For reasons of safety and environmental compatibility,

DO NOT burn, among other, plastic, painted wood,

coal or bark. Do not use the product as an incinerator.

The use of these fuels will invalidate the warranty.

First ignition procedure

• Make sure you have read and understood this

manual

• Remove

all ﬂ

ammable materials from the

appliance (manuals, labels, etc.). Make sure

you remove the labels on the glass. They would

irreparably damage the glass if they melted.

To light the ﬁ re in the combustion chamber, always

use smaller pieces of wood. Use larger pieces of

wood to feed the ﬁ re once it has started.

Place the wood on the combustion grille.

On ﬁ rst ignition, there may be a slight smell of paint,

which will disappear in a short time.

Always use the glove to touch any hot

parts. Avoid direct contact with hot parts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of EK63-EdilKamin Firek 3 in the language / languages: English as an attachment in your email.

The manual is 1.05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of EK63-EdilKamin Firek 3

EK63-EdilKamin Firek 3 Usermanual and installation guide - French - 28 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

EK63-EdilKamin Firek 3 Manual

Product: