810958

EK63-EdilKamin Firek 3 Manual

15
Zoom out
Zoom in
Previous page
1/24
Next page
15
fig. E
fig. F
fig. G
INSTALLATION
THE FUMES DUCT
THE FUMES DUCT
• if it is metal, it must have CE marking (EN 1856-2)
or some similar national standard marking;
• may not be made of fl exible metal material
• in order to check the fl ow, we recommend the use of
a damper if the draught is above 25 Pa
THE FLUE
THE FLUE:
• it must have a draught capable of creating
depressurisation, which is ideally around 12
Pa. Lower draughts may lead to leaks of smoke
when the door is opened; higher values tend to
generate fast combustion and reduced effi ciency
• must be correctly sized to satisfy the requirements
for fl ue gas discharging (EN 13384-1)
• must preferably be insulated, in steel with a
circular internal section. If rectangular, the internal
corners must have a radius of not less than 20
mm, with a ratio of the internal dimensions of
<1.5
• must normally be at least 3-4 metres in vertical
length
•must have a constant cross section
• must be waterproof and thermally insulated to
ensure a good draw
• must preferably have a collection chamber for
non-combusted matter and condensation
•must be at least in the T400 category with
appropriate resistance against soot igniting
•If pre-existing, must be clean, to prevent the fi
re
hazard.
THE CHIMNEY POT
THE CHIMNEY POT
• must be anti-downdraught
• must have an internal cross section equivalent to
that of the fl ue and a fumes outlet at least double
that of the interior of the fl ue
• for dual fl ues (which should be spaced at least 2
m apart) the chimney pot of the fl ue receiving the
fumes from the solid fuel appliance or that from
the higher storey, must be at least 50 cm higher
•needs to beyond the back fl ow zone
• it must allow for maintenance of the chimney.
EXTERNAL AIR INTAKE
The connection to the outside with a section of 300
cm2 is essential for the correction operation of the
fi replace.
This connection must connect the air vent of the
regulating mechanism (located on the side of the
mechanism) directly with the outside.
It can be done using a fl exible aluminium pipe
making sure that it is sealed at those points where air
dispersion could easily occur.
The aluminium pipe with a 20 cm diameter can
be positioned on the left or right of the regulating
mechanism.
We recommend applying a protection grille on the
outside of the air inlet duct which must not, however,
reduce the eff ective cross section of the intake.
The outside air must be taken at fl oor level (it cannot
come from high up).
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EK63-EdilKamin Firek 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EK63-EdilKamin Firek 3 in the language / languages: English as an attachment in your email.

The manual is 1.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of EK63-EdilKamin Firek 3

EK63-EdilKamin Firek 3 Usermanual and installation guide - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info