694714
34
Zoom out
Zoom in
Previous page
1/48
Next page
Chapter 5 Troubleshooting
5-1. No Picture
Problem Possible cause and remedy
1. No picture
Power indicator does not light up.
Check whether the power cord is connected properly.
Turn on the main power switch on the rear side of the monitor.
Touch
.
Turn off the main power switch on the rear side of the monitor, and
then turn it on again a few minutes later.
Power indicator is lighting white. Increase “Brightness”, “Contrast, or “Gain” in the Setting menu (see
“Color Adjustment” (page 23)).
Power indicator is lighting orange. Switch the input signal.
Turn the setting “On” for “Compatibility Mode” on the “Administrator
Settings” menu (see “Compatibility Mode” (page 32)).
Move the mouse or press any key on the keyboard.
Check whether the PC is turned on.
Turn off the main power switch on the rear side of the monitor, and
then turn it on again.
Power indicator is ashing orange
and white.
This symptom may occur during DisplayPort input.
- Use a signal cable recommended by us for the connection. Turn
the monitor off and on.
This symptom may occur during USB-C input.
- Disconnect and connect the USB cable that is plugged in to the
upstream port (USB-C).
- Turn off the main power switch on the rear side of the monitor, and
then turn it on again.
2. The message below appears. This message appears when the signal is not input correctly even
though the monitor is functioning properly.
This message appears when no
signal is input.
Example:
The message shown left may appear, because some PCs do not
output the signal immediately after power-on.
Check whether the PC is turned on.
Check whether the signal cable is connected properly.
Switch the input signal.
Turn off the main power switch on the rear side of the monitor, and
then turn it on again.
The message shows that the
input signal is out of the specied
frequency range.
Example:
Check whether the PC is congured to meet the resolution and
vertical scan frequency requirements of the monitor (see “1-3.
Supported Resolutions” (page 10)).
Reboot the PC.
Select an appropriate setting using the graphics board’s utility. Refer
to the User’s Manual of the graphics board for details.
This message shows that a device
that is not compatible with DP Alt
Mode is connected to the USB-C
connector.
Example:
Check whether a signal cable recommended by us is used.
Check whether the connected device is compatible with DP Alt
Mode. Contact the device manufacturer for information about
compatibility with DP Alt Mode.
Please connect it via a DisplayPort cable or HDMI cable.
34
Chapter 5 Troubleshooting
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eizo FlexScan EV3285 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eizo FlexScan EV3285 in the language / languages: English as an attachment in your email.

The manual is 2,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eizo FlexScan EV3285

Eizo FlexScan EV3285 Installation Guide - English, German - 4 pages

Eizo FlexScan EV3285 User Manual - German - 50 pages

Eizo FlexScan EV3285 Installation Guide - Dutch, French - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info