Manual Einhell WW 2000 R (page 15 of 72) (English, German, Dutch, French, Italian, Portuguese, Spanish)

605984

Zoom out

Zoom in

1/72

- 15 -

5. Before starting the equipment

Observe point 1 - Safety information.

Controls (buttons) (Fig. 2)

10 Desired Temperature + / Time Preselection +

11 Function Selection

12 On/Standby

13 Desired Temperature - / Time Preselection -

14 Time Preselection

Inserting batteries (Fig. 3-4):

1. Open the battery compartment cover by

pressing the lock (A) towards the middle and

pulling the battery compartment out at the

same time.

2. Insert the battery (B) in the battery compart-

ment with the positive pole facing down.

3. Press the battery compartment cover into the

remote control.

As the end user you are legally required to return

spent batteries. You can hand them in at public

collection points provided by your council or sales

outlets where batteries of this type are sold.

6. Operation

Warning! Before using the equipment for the ﬁ rst

time, check that the voltage supply is the same as

the voltage details set out on the rating plate.

•

Read the safety regulations in section 1.

•

When the equipment is used for the first time

or after a long period of rest, it may emit an

odor for a short time. This is not a fault.

All modes and functions can be set using the but-

tons on the appliance as well as with the remote

control. The remote control requires a CR 2032

button cell (included in delivery).

6.1 Switching on the appliance

The ON/OFF main switch (Fig. 1 / Item 4) is used

to disconnect the equipment completely from the

mains supply.

The ﬁ rst step when you want to use the appliance

is to turn on the main switch; the last step when

you no longer need the appliance is to turn oﬀ the

main switch. After the main switch is switched on,

the equipment will be in standby mode.

The heater shows the current equipment tem-

perature. The time display (00:00) for the timer

ﬂ ashes.

6.2 Heating mode (Fig. 2)

With the On / Standby button (Item 12) you can

switch the equipment on or to standby mode.

Press the On / Standby button (12) to switch on

the equipment. The desired temperature (default

setting 38°C) ﬂ ashes. The current equipment tem-

perature is then shown in the display, along with

the „Low heat output“ and „Blower“ symbols.

The time display (00:00) ﬂ ashes brieﬂ y and then

shows the operating time which has elapsed.

The heater operates with low heat output and the

blower.

Press the „Mode“ button (11) and by so doing

select the heating function in the following se-

quence.

Low heat output -> High heat output and blower

-> Frost protection function -> Low heat output

and blower -> Low heat output, etc.

6.3 Setting the desired temperature.

A desired temperature can be set between

5°C – 38°C, which is the temperature range of the

integrated temperature sensor (equipment tem-

perature). Press the „+“ or „-“ button to increase or

reduce the desired temperature.

For the equipment to heat, the desired tempera-

ture must be set higher than the indicated equip-

ment temperature. If the desired temperature is

exceeded by 2°C, the equipment will switch oﬀ

again.

In the frost protection function the temperature

is set to a default setting of 7°C and cannot be

adjusted.

6.4 Timer (Fig. 2)

Once you have ﬁ rst set the desired heating mode

and the desired temperature, you can program

a time for switching on („ON“) or a time for swit-

ching oﬀ („OFF“). You can select from between

1min to 23h 59min. It is also possible to combine

the switch-on time with the switch-oﬀ time.

Press the „Clock“ button (14) and select the timer

function in the following sequence.

Switch-on time hour -> Switch-on time minute ->

Switch-oﬀ time hour -> Switch-oﬀ time minute ->

Continuous operation

Anl_WW_2000_R_SPK7.indb 15Anl_WW_2000_R_SPK7.indb 15 13.03.15 09:3413.03.15 09:34

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell WW 2000 R in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell WW 2000 R Manual

Product: