Manual Einhell TH-CD 24-2 i (page 18 of 96) (English, Danish, Swedish, Norwegian)

606181

Zoom out

Zoom in

1/96

- 18 -

5. Before starting the equipment

Be sure to read the following information before

you put the cordless screwdriver into operation:

1. Charge the battery only with the charging unit

supplied.

2. Only ever use sharp drill bits and screwdriver

bits which are suitable for the purpose and in

faultless condition.

3. Always check for concealed electric cables

and gas and water pipes when drilling and

screwing in walls.

Additional handle (Fig. 1 /Item 13)

The additional handle (13) enables you to achieve

better stability whilst using the equipment.

The additional handle (13) is secured to the

housing by a clamp. It can be screwed to the right

or left side.

6. Operation

6.1 Charging the battery (Fig. 2-3)

1. Remove the battery pack (5) from the handle

(Fig. 2) by pressing the pushlock buttons (8)

on the left and right side of the battery pack

(5).

2. Check that your mains voltage is the same as

that marked on the rating plate. Plug the char-

ging cable (7) of the charging unit (6) into the

power socket. The green LED on the charging

unit then comes on.

3. Insert the battery pack (5) into the battery

charger (6). The red LED will come on to in-

dicate that the battery pack is being charged.

Charging has ﬁ nished when the red LED

goes out and the green LED comes on again.

The battery pack may become a little warm

during the charging process. This is normal.

Caution! At temperatures of 45°C and higher the

battery cannot be charged. In this case remove

the battery from the charger, let it cool down and

then recharge it.

If the battery pack fails to charge, check for the

following:

•

Voltage at the power socket

•

Good contact at the charging contacts of the

charging unit

If the battery pack still fails to charge, send

•

the charging unit

•

and the battery pack

to our customer service center.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly.

You must recharge the battery pack when you

notice that the power of the cordless equipment

drops. Never fully discharge the battery pack. This

will cause it to develop a defect!

6.2 Torque setting (Fig. 4 / Item 1)

The cordless hammer drill/screwdriver is ﬁ tted

with a mechanical torque selector.

The torque for a particular screw size is set with

the setting ring (1). The torque is dependent on a

number of factors:

•

On the type and hardness of the material in-

volved

•

On the type and length of the screws used

•

On the requirements that the screw connec-

tion has to satisfy

The grating disengagement of the coupling in-

dicates that the selected torque level has been

reached.

Caution! Only ever adjust the setting ring

when the equipment is at a standstill.

6.3 Drilling/hammer drilling (Fig. 4)

•

For drilling purpose, adjust the torque setting

(1) to the setting “Drill”.

•

For hammer drilling purpose, adjust the

torque setting (1) to the setting “Hammer”.

In the drill and hammer drill settings the slip cou-

pling is non-functional. The maximum torque is

available for drilling and hammer drilling.

6.4 Changeover switch (Fig. 5/Item 3)

The slide switch above the On/Oﬀ switch is for

setting the direction of rotation of the cordless

screwdriver and for preventing the cordless

screwdriver from being switched on inadvertently.

You can select between clockwise and counter-

clockwise rotation. To avoid causing damage to

the gearing, the direction of rotation must only be

changed when the screwdriver is at a standstill.

When the slide switch is in the middle position,

the On/Oﬀ switch is blocked.

Anl_TH_CD_24_2_i_SPK1.indb 18Anl_TH_CD_24_2_i_SPK1.indb 18 07.08.12 16:5907.08.12 16:59

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Einhell TH-CD 24-2 i in the language / languages: English, Danish, Swedish, Norwegian as an attachment in your email.

The manual is 1,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Einhell TH-CD 24-2 i

Einhell TH-CD 24-2 i User Manual - German, Dutch, French, Italian, Portuguese, Spanish - 64 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Einhell TH-CD 24-2 i Manual

Product: